Bosch GCU 18V-30 Professional Manual Original página 13

Never service damaged battery packs. Service of bat-
u
tery packs should only be performed by the manufacturer
or authorized service providers.
Safety instructions for edge routers
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the work by your hand or against the body leaves it un-
stable and may lead to loss of control.
The permitted speed of the cutting bit must be at least
u
equal to the maximum speed marked on the power
tool. If cutting bits run faster than their rated speed, they
may break and fly off.
Routers and other accessories must be able to fit ex-
u
actly in the tool holder (collet) of your power tool. Ap-
plication tools that do not fit exactly in the tool holder of
the power tool will turn unevenly, vibrate heavily and may
cause a loss of control.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Never rout over metal objects, nails or screws. The
u
router could become damaged and cause increased vibra-
tion.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Do not use blunt or damaged routers. Blunt or damaged
u
routers cause increased friction, create imbalances and
may become jammed.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Bosch Power Tools
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting plaster, plastic, dry-
walls and non-metallic light construction materials.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
a)
(1) Application tool
(2) Adjustable depth stop
(3) Adapter for dust extraction
(4) Worklight
(5) On/off switch
a)
(6) Rechargeable battery
a)
(7) Battery release button
(8) Spindle lock button
(9) Fastening screw for adjustable depth stop
(10) Handle (insulated gripping surface)
(11) Collet
(12) Collet nut
(13) Open-ended spanner (16 mm)
(14) Output shaft
a)
(15) Extraction hose
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Spiral saw
Article number
Rated voltage
A)
No-load speed
Connection for dust extraction
Compatible collets
Weight according to
B)
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
English | 13
GCU 18V-30
3 601 JK8 0..
V= 18
-1
min 30,000
●
mm 3.17 (1/8")/
3.96 (5/32")/
6.35 (1/4")
kg 1.3–2.6
°C 0 to +35
1 609 92A 8A2 | (02.09.2022)