Roland XV-3080 Manual Del Usuario página 176

Implementación MIDI
Controller Reset value
Pitch Bend Change +/-0 (center)
Polyphonic Key Pressure 0 (off)
Channel Pressure 0 (off)
Modulation 0 (off)
Breath Type 0 (min)
Expression 127 (max)
Hold 1 0 (off)
Sostenuto 0 (off)
Soft 0 (off)
Hold 2 0 (off)
RPN unset; previously set data will not change
NRPN unset; previously set data will not change
G Desactivación de Notas (Controller number 123)
Status 2nd byte
BnH 7BH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
* When All Notes Off is received, all notes on the corresponding channel will be turned
off. However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are
turned off.
G OMNI OFF (Controller number 124)
Status 2nd byte
BnH 7CH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
G MNI ON (Controller number 125)
Status 2nd byte
BnH 7DH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received. OMNI ON
will not be turned on.
G MONO (Controller number 126)
Status 2nd byte
BnH 7EH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
mm = mono number: 00H - 10H (0 - 16)
* The same processing will be carried out as when All Notes Off is received.
* In Performance mode, the Part Mono/Poly parameter (PERFORM/PART) will change.
G POLY (Controller number 127)
Status 2nd byte
BnH 7FH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
* In Performance mode, the Part Mono/Poly parameter (PERFORM/PART) will change.
I Mensaje del Sistema a Tiempo Real
G Reloj de Temporización
Status
F8H
* This message will be received if the Clock Source parameter (SYSTEM/COMMON) is
MIDI.
G Sensibilidad Activa
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of all
further messages. While monitoring, if the interval between messages exceeds 420 ms,
the same processing will be carried out as when All Sounds Off, All Notes Off and Reset
All Controllers are received, and message interval monitoring will be halted.
176
3rd byte
00H
3rd byte
00H
3rd byte
00H
3rd byte
mmH
3rd byte
00H
I Mensaje Exclusivo del Sistema
Status Data byte
F0H iiH, ddH, ......,eeH
F0H: System Exclusive Message status
ii = ID number: an ID number (manufacturer ID) to indicate the manufacturer whose
Exclusive message this is. Roland's manufacturer ID is 41H.
ID numbers 7EH and 7FH are extensions of the MIDI standard; Universal Non-realtime
Messages (7EH) and Universal Realtime Messages (7FH).
dd,...,ee = data: 00H - 7FH (0 - 127)
F7H: EOX (End Of Exclusive)
Of the System Exclusive messages received by this device, the Universal Non-realtime
messages and the Universal Realtime messages and the Data Request (RQ1) messages and
the Data Set (DT1) messages will be set automatically.
G Mensajes Universales Exclusivos del SIstema No a
Tiempo Real
❍ Identity Request Message
Status Data byte
F0H 7EH, dev, 06H, 01H F7H
Byte Explanation
F0H Exclusive status
7EH ID number (Universal Non-realtime Message)
dev Device ID (dev: 00H - 1FH (1 - 32), the initial value is 10H (17).)
06H Sub ID#1 (General Information)
01H Sub ID#2 (Identity Request)
F7H EOX (End Of Exclusive)
* When this message is received, Identity Reply message (p.$$$) will be transmitted.
❍ GM1 System On
Status Data byte
F0H 7EH, 7FH, 09H, 01H F7H
Byte Explanation
F0H Exclusive status
7EH ID number (Universal Non-realtime Message)
7FH Device ID (Broadcast)
09H Sub ID#1 (General MIDI Message)
01H Sub ID#2 (General MIDI 1 On)
F7H EOX (End Of Exclusive)
* When this messages is received, this instrument will turn to the GM1 mode.
* Not received when the Receive GM1 System On parameter (SYSTEM/COMMON) is
OFF.
❍ GM2 System On
Status Data byte
F0H 7EH 7FH 09H 03H
Byte Explanation
F0H Exclusive status
7EH ID number (Universal Non-realtime Message)
7FH Device ID (Broadcast)
09H Sub ID#1 (General MIDI Message)
03H Sub ID#2 (General MIDI 2 On)
F7H EOX (End Of Exclusive)
* When this messages is received, this instrument will turn to the GM2 mode.
* Not received when the Receive GM2 System On parameter (SYSTEM/COMMON) is
OFF.
❍ GM System Off
Status Data byte
F0H 7EH,7F,09H,02H
Byte Explanation
F0H Exclusive status
7EH ID number (Universal Non-realtime Message)
Status
F7H
Status
Status
Status
F7H
Status
F7H