Tiempo Real - Roland XV-3080 Manual Del Usuario

Implementación MIDI
❍ Vibrato Rate (Controller number 76)
Status 2nd byte
BnH 4CH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
vv = Vibrato Rate value (relative change):
❍ Vibrato Depth (Controller number 77)
Status 2nd byte
BnH 4DH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
vv = Vibrato Depth Value (relative change):
❍ Vibrato Delay (Controller number 78)
Status 2nd byte
BnH 4EH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
vv = Vibrato Delay value (relative change):
❍ Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte
BnH 5BH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
vv = Reverb Send Level: 00H - 7FH (0 - 127)
❍Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte
BnH 5DH
n = MIDI channel number: 0H - FH (Ch.1 - 16)
vv = Chorus Send Level: 00H - 7FH (0 - 127)
❍RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte
BnH 65H
BnH 64H
n = MIDI channel number: 0H - FH (Ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
This device receives the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB
00H, 00H mmH, llH
00H, 01H mmH, llH
00H, 02H mmH, llH
7FH, 7FH ---, ---
180
3rd byte
vvH
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
* In Performance mode, the Part Pitch Bend
Range parameter (PERFORM/PART)
change.
Master Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H (-8192 x 50 /
8192 - 0 - +8192 x50 / 8192 cent)
* In Performance mode, the Part Fine Tune
parameter (PERFORM/PART) will change.
Master Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
* In Performance mode, the Part Coarse Tune
parameter (PERFORM/PART) will change.
RPN null
RPN and NRPN will be set as "unspecified".
Once this setting has been made, subsequent
Parameter values that were previously set will
not change.
mm, ll: ignored
GCambio de Programa
Status 2nd byte
CnH ppH
n = MIDI channel number:
pp = Program number: 00H - 7FH (prog.1 - prog.128)
IMensajes Exclusivos del Sistema
Universal Non-realtime System Exclusive Message" and Data Set 1 (DT1) are the only
System Exclusive messages transmitted by the XV-3080.
GMensajes Universales Eclusivos del SIstema No a

Tiempo Real

❍Identity Reply Message
Receiving Identity Request Message, the XV-3080 send this message.
Status Data byte
F0H 7EH, dev, 06H, 02H, 41H, 10H, 01H, 00H, 00H, 00H, 00H, 00H, 00H
F7H
Byte Explanation
FOH Exclusive status
7EH ID number (Universal Non-realtime Message)
dev Device ID (use the same as the device ID of Roland)
06H Sub ID#1 (General Information)
02H Sub ID#2 (Identity Reply)
41H ID number (Roland)
10H 01H Device family code
00H 00H Device family number code
00H 00H 00H 00H Software revision level
F7H EOX (End of Exclusive)
GTransmisión de Datos
❍Data set 1
DT1 (12H)
Status Data byte
F0H 41H, dev, 00H, 10H, 12H, aaH, bbH, ccH, ddH, eeH, ... ffH, sum F7H
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 00H - 1FH, Initial value is 10H)
00H Model ID #1 (XV-3080)
10H Model ID #2 (XV-3080)
12H Command ID (DT1)
aaH Address MSB: upper byte of the starting address of the data to be sent
bbH Address: upper middle byte of the starting address of the data to be sent
ccH Address: lower middle byte of the starting address of the data to be sent
will
ddH Address LSB: lower byte of the starting address of the data to be sent.
eeH Data: the actual data to be sent. Multiple bytes of data are transmitted in order
starting from the address.
: :
ffH Data
sum Checksum
F7H EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and
data will be transmitted from the specified starting address and size. Refer to the
Address and Size given in Section 3, "Parameter address map."
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each
packet will be sent at an interval of about 20 ms.
0H - FH (Ch.1 - 16)
Status
Status