Publicidad
Idiomas disponibles
Idiomas disponibles
3Dpureairfunction(adjustablegrid)
You can adjust the position of the air outlet grid manually, as desired. For an optimum, even flow
of purified air in the room, set the angle to 45°; for maximum comfort, set the angle to 90°.
ControlPanelLock
The lock system prevents the purifier from being accidentally mis-set during operation.
To activate it, press the button (7) for 3 sec until the locked control panel indicator turns on. To exit
this mode, press the button (7) again for 3 seconds, until the indicator turns off. When selected, the
other buttons are locked.
Wi-fifunction
Frequency band operated : 2400-2483,50MHz
Maximum radio-frequency power : 20dbm
To turn on or off the Wi-Fi function on your purifier, hold simultaneously the Wi-Fi button
the Light button
during 3 seconds.
• When the Wi-Fi connection indicator
Reset
Press together the LIGHT
+ LOCK
First, the appliance will make a long bip to indicate Reset is launched. Then the appliance should
erase all data regarding pairing.
Once it's done, the product will turn off.
Indicationofairquality
Air quality indicator (A) is located on the top of the appliance.
AirQuality
Excellent
Slight pollution
Moderate pollution
High pollution
Extreme pollution
HOW TO CONNECT YOUR PURIFIER TO INTERNET ?
Download the app «Pure Air By Rowenta» /«Pure Air by Tefal» & follow the instructions on your
smartphone :
1. Sign in to create your Rowenta/Tefal account if you are new. Or log in the app if you already
have an account.
2. Make sure to stand close to the purifier during the pairing (2 meters maximum) and make
sure the purifier is located near a strong Wi-Fi signal.
3. Make sure your phone is connected to your local Wi-Fi network.
4. Turn your purifier on & hold the Wi-Fi button for 3 seconds (you'll hear a «ding» sound and
the Wi-Fi indicator will flash to indicate that your purifier is successfully connected to Wi-Fi.)
5. Choose your Wi-Fi network and enter the network password to connect to your local
Wi-Fi network.
6. And you're done !
The Wi-Fi indicator lights to indicate that your purifier is successfully connected to your Pure Air app.
Connection issues
In case of pairing issues between the appliance and your domestic Wi-Fi network, refer to the
information listed on the following link:
https://www.compatibility.groupeseb.com/CompatibilityList-Pureair-Rowenta.pdf
https://www.compatibility.groupeseb.com/CompatibilityList-Pureair-Tefal.pdf
18
flashes it means that the purifier losts its connection.
buttons for 3 seconds.
Airqualityindicatorcolor
Blue
Green
Yellow
Orange
Red
MAINTENANCE
Always switch the appliance off with the button (9) and unplug it before conducting any maintenance operation.
You can clean the appliance with a slightly damp cloth.
IMPORTANT: Never use abrasive products which could damage your appliance's appearance.
FILTERS
Filter
Pre-filter
Active carbon filter
Allergy+ filter
These figures are based on tests in which the air purifier is used for 8 hours per day in quiet mode.
and
The recommended frequency for cleaning and replacing the filters may vary depending on the
duration of use and the operating environment.
• A
light indicates when the allergy+ filter needs to be replaced.
The
light display indicates when the carbon filter needs replacing.
• The pre-filter can be re-used: remove the dust using a vacuum cleaner or wash with water.
CAUTION:
• The appliance's efficiency can be reduced if the pre-filter is not cleaned regularly.
•
Never use a pre-filter that is still damp.
•
The pre-filter is the only filter which can be re-used and washed with water. The particle, and active
carbon filters cannot be cleaned and re-used. Never wash with water.
•
To replace the filters, follow the instructions in the section « Disassembling/Reassembling filters ».
Your replacement filters are available under the following codes:
Filtre
Allergy+ filter
Active carbon filter
IMPORTANT: Resetting the filters
The reset light flashes when a filter needs to be replaced or cleaned (Prefilter). Once the filter has
been replaced, hold down the reset button for 3 seconds.
Forced reset:
If you have replaced a filter before its end of life, force the reset of the filter replacement cycle:
1. Hold the reset button for 3 seconds.
2. Press the reset button briefly to select the filter you have changed.
3. After selecting the filter to reset, hold the reset button for 3 seconds. The new filter life is then
reset.
4. If the reset filter button is not is activated for 10 seconds in forced reset mode, the reset mode
is canceled.
« TIPS FOR CHANGING FILTERS »
• Avoid handling used filters if you suffer from allergies or asthma.
• Wear gloves when changing the filters, or wash your hands well afterwards.
• Put used filters directly into a closed, air-tight bag before throwing them away to
avoid spreading pollutants.
Action
Cycles
Clean
Every 2 to 4 weeks
Replace
Every 12 months
Replace
Every 2 years
PU/PT618x
XD6077
XD6061
.
.
EN
FR
19
Publicidad
