Publicidad
Idiomas disponibles
Idiomas disponibles
Note: You can select a different type of hot drink by pressing a different preset
button while the kettle is operating. This is only possible if the temperature of
the water is still below the temperature of the newly pressed button.
Keeping water warm
You can use the keep-warm function to keep water warm for 30 minutes at
the temperatures of the different preset buttons (40°C, 80°C, 90°C, 95°C
or 100°C).
Note: Only use the keep-warm function in combination with a preset button.
Only use the keep-warm function when there is at least 0.25l water in
the kettle. If there is too little water in the kettle, the kettle may switch
off before the 30 minutes have elapsed to protect the heating element.
Keeping water warm at a desired temperature
Press a preset button to set the desired temperature (see section
1
'Heating up water with preset buttons' in this chapter).
Press the KEEP WARM button (Fig. 11).
2
, When the kettle heats up the water to keep it at the selected
temperature, the light ring around the KEEP WARM button lights up
continuously.
, When the water has reached the selected temperature, the light ring
around the KEEP WARM button slowly pulsates until the keep-warm
function is cancelled or switches off automatically after 30 minutes.
Note: If you press the KEEP WARM button before you press a preset button,
nothing happens. If you have just prepared hot water, you can press the same
preset button again and then press the KEEP WARM button.
The kettle keeps the water warm for 30 minutes.
3
, After 30 minutes, you hear an audible signal and the appliance
switches off automatically.
Note: You can stop the keep-warm process at any time. To do so, press the KEEP
WARM button again, press the selected preset button or remove the kettle
from the base.
Note: If you remove the kettle from the base, the set keep-warm temperature
is lost.
Note: If you press another preset button while the keep-warm function is
activated, the keep-warm function switches off and the kettle starts heating up
the water to the temperature of the preset button.
Note: If the keep-warm function has not been activated, the appliance switches
off automatically after 5 minutes of inactivity.
Cleaning and descaling
Always unplug the base before you clean it
Always remove the kettle from the base before you clean the kettle.
Never immerse the kettle or its base in water.
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the appliance.
Cleaning the kettle and the base
Clean the outside of the kettle and the base with a soft cloth
1
moistened with warm water and some mild cleaning agent.
Caution: Do not let the moist cloth come into contact with the cord, the
plug and the connector of the base.
Cleaning the filter
Scale is not harmful to your health but it may give your drink a powdery
taste. The anti-scale filter prevents scale particles from ending up in your
drink.
Clean the single-action filter regularly in the following way:
Take the filter out of the kettle (Fig. 12).
1
Gently clean the filter with a soft nylon brush.
2
Slide the filter back into the kettle.
3
Note: HD9385 only: The filter at the bottom of the kettle cannot be removed.
You can clean this filter by descaling the kettle, see section 'Descaling the kettle'
below.
Descaling the kettle
Regular descaling prolongs the lifetime of the kettle.
In case of normal use (up to 5 times a day), the following descaling
frequency is recommended:
-
Once every 6 months for areas with low water hardness.
All manuals and user guides at all-guides.com
-
Once every 3 months for areas with average water hardness.
-
Once every month for areas with high water hardness.
Fill the kettle with white vinegar (8% acetic acid) up to one quarter of
1
the MAX indication.
Add water to the MAX indication.
2
Press the green tea button to heat up the water to 80ºC and then
3
press the KEEP WARM button.
Empty the kettle after 30 minutes and rinse the inside thoroughly.
4
Repeat the descaling procedure if there is still some scale in the kettle.
5
Note: You can also use an appropriate descaler. In that case, follow the
instructions on the package of the descaler.
Note: If you take the kettle off the base before the descaling process is finished,
the appliance switches off automatically. You can also deactivate the descaling
process by pressing any of the preset buttons.
storage
-
To store the cord, wind it around the cord storage facility in the bottom
of the base (Fig. 2).
Ordering accessories
To purchase accessories for this appliance, please visit our online shop at
www.shop.philips.com/service. If the online shop is not available in
your country, go to your Philips dealer or a Philips service centre. If you have
any difficulties obtaining accessories for your appliance, please contact the
Philips Consumer Care Centre in your country. You find its contact details in
the worldwide guarantee leaflet.
Environment
-
Do not throw away the appliance with the normal household waste
at the end of its life, but hand it in at an official collection point for
recycling. By doing this, you help to preserve the environment (Fig. 13).
guarantee and service
If you need service or information or if you have a problem, please visit
the Philips website at www.philips.com/support or contact the Philips
Consumer Care Centre in your country. You find its phone number in the
worldwide guarantee leaflet. If there is no Consumer Care Centre in your
country, go to your local Philips dealer.
Troubleshooting
This chapter summarises the most common problems you could encounter
with the appliance. If you are unable to solve the problem with the
information below, visit www.philips.com/support for a list of frequently
asked questions or contact the Consumer Care Centre in your country.
Signal
The light ring around one
preset button lights up while
the other light rings are off.
The light ring of the preset
button I pressed flashes 3
times.
The kettle beeps.
Problem
Possible solution
I cannot set the
The current temperature of the water in the kettle
desired tempera-
is probably higher than the temperature you want to
ture.
set. You can add cold water to the kettle. If you wish
to reheat the water immediately, you can only select
100ºC.
I try to switch
When there is no water in the kettle, the boil-dry
on the kettle but
protection trips and the kettle switches off automati-
it switches off
cally. You may need to put more water in the kettle
automatically.
(at least 0.25 litres).
The kettle is not placed on its base correctly. Re-
move the kettle from the base and correctly place it
on the base again.
The kettle
The kettle keeps the water warm for 30 minutes and
switches off au-
then switches off automatically. To keep the water
tomatically when
warm longer, press the KEEP WARM button again
the keep-warm
after it has finished.
function is active.
Meaning/solution
After the water has reached the set tem-
perature, the light of the selected preset
button stays on for 5 minutes.
The temperature of the water is higher
than the temperature of the selected
preset button.
The water has reached the set tempera-
ture.
Publicidad
