INSTRUCTION MANUAL
Thank you for purchasing this high quality Fan. Our fans have been carefully designed and constructed to meet the
highest standards of performance, quality and safety. Please read the instructions carefully to ensure satisfactory
and trouble free use.
YOUR FAN FEATURES
•
3 Speed Control
•
Oscillation over an Angle of 80°
•
Protective Grille
•
Adjustable for height
•
220-240V • 50Hz • 50W
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed, including the following:
•
Read all instructions carefully and save these instruction manual for reference.
•
To protect against electric shock, do not immerse cord, plug or fan into water or any other liquid.
•
Do not use appliance for other than intended use.
•
Use the appliance only on the voltage specified on its rating plate (220-240V/50Hz).
•
Unplug from outlet when not in use and before cleaning.
•
Do not pull the connection cord over sharp edges and never jam it.
•
Do not pull the plug out of the socket by pulling the connection cord.
•
Do not use outdoors.
•
Do not use an extension cord, unless the cord has been checked and tested by your electrical authority or a
qualified technician.
•
Close supervision is necessary when any appliance is used by or near children.
•
Always use your appliance on a suitabel level and dry platform.
•
Avoid using an appliance where it can fall or be pushed into water. Never reach for an appliance after it has fallen
into water. Switch off at the mains power point und unplug immediately.
•
Never attempt to insert any object through the grille when the fan is operating.
•
Always disconnect fan when moving from one location to another.
•
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been
damaged in any manner.
•
Do not cover the grille.
•
Do not spray pesticide towards. It may make the resin and coating bad or broken.
•
Do not use the fan in such place where the curtain may be drawn in.
•
Do not use before assembly.
•
Do not use in the high temperature (above 40°C), high humidity (bathroom) and dusty places or the places
where there is acid alkali oil, etc.
•
The babies, patients and old men should not be blown directly for a long time.
•
If the fan is to be stored for an extended period of time or not used regularly, replace it in the original packaging
(or similar) and store it in a dry and clean place. Before using again, check if the unit is clean and dry and if the fan
blades rotates freely.
•
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
•
Children should be supervised to ensure that they do not play with the appliance.
•
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped
or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or
electrical or mechanical adjustment.
•
If the supply cord is damaged it must be replaced by the manufacturer or a authorized service agent or a
qualified technician in order to avoid a hazard.
•
Never leave the appliance unsupervised when in use.
•
Never use accessories that are not recommended by the producer. They could constitute a danger to the user and
risk to damage the appliance.
•
It is absolutely necessary to unplug the appliance before assembling the base or any other part or before
disassembling it.
•
Make sure the appliance is switched to the "0" position before unplugging it.
•
Do not insert your fingers, pencils, or any other objects in the protection guard.
•
Adequate air space should be provided for air circulation.
•
Under no circumstances must the appliance come into contact with curtains, clothing, dish towels or other
flammable materials during use.
2
DESCRIPTION OF PARTS (picture 1)
1. Front guard
7. Rear Guard
2. Guard screw
8. Electrical axle centre
3. Decoration cover
9. Motor shaft bolt
4. Blade Fastening screw
10. Front shell
5. Fan Blade
11. Rear shell
6. Guard Fastening screw
12. Oscillate control knob
ASSEMBLY INSTRUCTIONS
Please assemble correctly by the following orders when using:
1. ASSEMBLY THE STAND (picture 2)
•
Fix the cross bars (18).
•
Put the standing shaft (17) on the cross bars.
•
Screw the standing shaft on the cross bars with four screws.
2. THE WHOLE ASSEMBLY (picture 3)
•
Loosen the fixing screw (16) and pull the electroplated shaft (15) to the height needed and then fix it firmly.
•
Link the fan main body and the adjustable electroplated shaft (15) together by the fixing screw (14) and then fix
them.
3. REAR NET ASSEMBLY (picture 4)
•
Screw the net fastening screw (6) out in anti-clockwise direction.
•
Fix the rear guard (7) onto the two pillars of the motor front shell.
•
Screw the net fastening screw (6) tightly in clockwise direction.
4. THE ASSEMBLY OF FAN BLADE (picture 5)
•
Put the fan blade into the electrical axle centre and the axle centre bolt must be pressed to the end of the
concave notch at the back of the fan blade. They must be tallied completely.
•
Screw the screw into the electrical axle centre in anti-clockwise direction and then fix it.
5. FRONT NET ASSEMBLY (picture 6)
•
The safety grille has five clips that you now need to lift to complete the assembly.
•
Align the top locking clip to the top of the rear safety grille. Lock the side clips in place and align the bottom hole
for the security nut and bolt. Undo the security lock and bolt and thread the aligned holes in the security tools
before doing up the bolt with a pair of pliers or a similar tool.
OPERATING INSTRUCTIONS
•
This fan has three types of speed control.
Strong
3
Middle
2
Piano switches of the wind adjusting
Weak
1
0
OFF Switch
•
You can choose the up and down angle and control the wind direction freely.
•
Press the oscillate control knob, the fan begins to wave. Pull the button, the fan stops waving.
•
Heigth regulation:
Loosen the fastening screw (16), regulate the electroplated pipe to the needed height.
Repairs:
Danger: Electrical appliances must only be repaired by authorized specialists. Because damages can occur by
nonauthorized repairs. In the case of a repair, contact your retailer or contact the producer.
Environment friendly disposal
You can help protect the environment! Please remember to respect the local regulations: hand in the non-
working electrical equipments to an appropriate waste disposal center.
13. Speed switch
14. Fastening screw
15. Adjustable electroplated shaft
16. Fastening screw
17. Standing shaft
18. Cross Base
3