Profi Care PC-BSR 3108 Manual De Instrucciones página 19

CAUTION:
• If something gets stuck in the nozzle during operation
and obstructs the appliance, switch off the appliance
immediately and remove the obstruction.
1. Before each use, make sure that the dust container and
filters are inserted and empty or cleaned.
2. Briefly press and hold the
switch it on.
3. Press the button. If the room conditions allows it, the
appliance cleans the room in zigzag mode.
4. If necessary, select another cleaning mode.
5. The appliance cleans the floor until it has completely
cleaned the room or the battery capacity has dropped to
about 15 %. The appliance then automatically returns to
the charging station.
- If you press the button, the appliance stops
operating and searches for the charging station, even
if there is still enough battery charge.
Using the Appliance with the Wiping Function
Before using the appliance as described previously, mount
the water tank with the attached cleaning fleece. See also
illustrations J to K on page 4.
1. If necessary, remove the cleaning fleece to be able to
open the water tank cap.
2. Open the rubber cover of the water tank and fill the water
tank. If necessary, add some cleaning agent to the water.
3. Attach the cleaning fleece to the water tank and place
the water tank on the underside of the appliance.
4. Important! Start the operation of the appliance imme-
diately to avoid damage to the floor covering by the
dripping water!
The condition of the floor covering is decisive for the wiping
result.
Ending Operation
1. Stop the appliance by pressing the
2. Switch off the appliance by pressing and holding the
button for approx. 4 seconds.
3. Remove the water tank and pull off the cleaning fleece.
Empty the dust container and clean the filters and sen-
sors as well as the cleaning fleece as described under
"Maintenance and Cleaning".
Maintenance and Cleaning
WARNING:
• Always switch off the appliance before maintenance
or cleaning!
• Never immerse the appliance in water for cleaning. It
could cause an electric shock or fire.
PC-BSR3108_IM
button on the appliance to
button.
CAUTION:
• Do not use a wire brush or other abrasive objects.
• Do not use harsh or abrasive cleaners.
Do not attempt to lubricate the rollers with grease or oil. This
would cause dust or dirt to stick to the rollers more.
• Clean the housing with a soft, dry cloth without any
additives.
• Clean the sensors (10 / 14 / 17) carefully with a dry soft
cloth.
CAUTION:
Check that the sensors are clean after and before
each use. Otherwise the appliance could fall down a
staircase.
• After and before each use, make sure the nozzle and air
vents are clear.
• For a good performance of the appliance, empty the dust
container and clean the filters after each use.
Emptying the Dust Container and Cleaning the Filters
CAUTION:
Never wash the filters.
Also refer to illustrations D to I on page 4.
1. Remove the water tank, if still attached.
2. Reach into the recess and press the lock. Now you can
pull the dust container out of the appliance. (Illustra-
tion D)
3. Fold the dust container apart and lift the cover for the
HEPA filter. (Illustration E)
4. Pull the HEPA filter out of the dust container. (Illustra-
tion F)
5. Clean the HEPA filter and the socket by gently tapping
them out.
We recommend replacing the HEPA filter once a year.
CAUTION:
Do not use a brush to clean the HEPA filter. Using a
brush could damage the filter material.
6. Empty the dust container over a dustbin. (Illustration G)
7. You can clean the dust container under running water.
Clean the frame with a soft brush. (Illustration H)
CAUTION:
• Allow the dust container to air dry. However, do not
place it in the sunshine.
• Only reinsert the filters in the dust container when
they are completely dry!
8. Put the filters back into the dust container. Make sure
that both the socket and the HEPA filter are inserted
correctly. (Illustration I)
9. Put the dust container back into the appliance. It should
lock into place with a "click".
19
17.04.23