Publicidad
Idiomas disponibles
Idiomas disponibles
G B
THIS EQUIPMENT IS COMPLIANT WITH THE FOLLOWING STANDARDS:
EN 60 335-1:2012+A11:2014, EN 60 335-2-31:2014, EN 62233:2008 + C1:2008, EN 61 000-3-2:2006 + A1/A2: 2009, EN
61 000-3-3:2008, EN 55 014-1:2006 + A1:2009 + A2:2011, EN 55 014-2:1997 + A1:2001 + A2:2008, EN 61591:1997/
A2:2011, EN 50564:2011, EN 50581:2012, 2014/35/CE relating to electrical safety, 2014/30/EC relating to electromagnetic
compatibility, 2009/125/EC relating to ecodesign, 2011/65/EC relating to the limitation of the use of certain hazardous
substances in electrical and electronic equipment and to the main requirements of European Directives 66/2014.
When the symbol of a crossed out wheelie bin is attached to a product it means that the product is covered by the European Di-
rective 2002/96/EC.
Your product is designed and manufactured with materials and components of high quality that can be recycled and used again:
•
You should find out about the local system of separation of electrical and electronic waste,
•
You should act according to the local rules and not dispose of your used product with normal domestic waste,
•
Correct disposal of your old product will help prevent the potential negative consequences on the environment and
human health.
This appliance must not be used by persons (including children) with diminished psychical, sensory or mental capacities,
nor by persons not having the experience and knowledge of this type of appliance, unless they are under the control
and the training of persons responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
Assembly and connection must be done by a qualified installer
Use suitable anchors for the support medium. Obtain information from the manufacturers; seal if necessary. The company dis-
claims any responsibility in case of faulty anchoring due to the hole or the anchor system.
The hood is equipped with a HO5VVF 3 x 0.75 mm² power cable with a standard 10/16A plug with earth.
Mode of protection: class 1
Supply voltage: 220-240V single phase - 50/60Hz.
Check that the mains voltage is the same as the values indicated on the manufacturer's plate on the inside of the hood.
If the hood is connected directly to the mains (without a plug), an all-pole circuit breaker switch with a contact opening of 3 mm
GB
must be installed before the hood. The earth wire (yellow and green) must not be broken by this switch.
•
Respect the diameter of the appliance output: the hood must not in any circumstances be connected to a controlled mecha-
nical ventilation duct.
•
If it releases the stale air into an outlet duct, it is essential to ensure that the latter is not already used to carry gas or smoke
from appliances powered by energy other than electricity.
•
Position the cooking surface as close as possible to the outlet and avoid the formation of elbows in the duct, to reduce pres-
sure loss to the minimum.
•
When installing situations, make sure that the air renewal in the kitchen is satisfactory. Be sure to create one or more air inlets
with a section greater than or equal to the diameter of the outlet pipe in order not to create a vacuum in the kitchen.
•
Make sure there is sufficient ventilation if a cooking or other appliance uses the ambient air of the room where the hood is
installed at the same time.
•
The maximum vacuum created in the room should be less than 0.04 mbar; this prevents return of the combustion gases.
•
The appliance must be positioned in such a way that the power plug is accessible.
Failure to comply with this condition results in the cancellation of the manufacturer's warranty and rejection of any recourse in the event of an accident.
(1)
8
This manual applies to several appliance versions.
It may contain descriptions of accessories not included in your appliance.
ASSEMBLY RECOMMENDATIONS
.
(1)
Publicidad
