Publicidad
Idiomas disponibles
Idiomas disponibles
Switch 4: Programming of opening limit
switch of the rolling shutter
To set the opening limit switch on a rolling shutter with a
blockage at the top, you must have a previously stored remote
control available and must proceed with the following points.
1. Only feed power to the motor to be programmed
2. DOTTO multichannel only: press several times the key SELC of
the transmitter until displayed the channel stored
3. Take the rolling shutter to half its way by the keys UP or
DOWN
4. Set to ON the switch 4 of the transmitter
5. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor, moving for 1/2 second in
both the ways, proves it is entering into programming phase.
6. Release the key PROG
7. Press the key UP: the rolling shutter goes up at normal speed
8. Once in contact with the upper lock, it stops and memorizes
the position
9. Set to OFF the switch 4 of the transmitter
To set the opening limit switch on a rolling shutter without
blockage at the top, you must have a previously stored remote
control available and must proceed with the following points.
1. Only feed power to the motor to be programmed
2. DOTTO multichannel only: press several times the key SELC of
the transmitter until displayed the channel stored
3. Position the rolling shutter at the mid-height
4. Set to ON the switch 4 of the transmitter
5. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor, moving for 1/2 second in
both the ways, proves it is entering into programming phase
6. Release the key PROG
7. Position the rolling shutter in the UPPER position desired using
the UP and DOWN buttons. To regulate it precisely, press the
PROG button when the motor is close to the limit switch. the
motor will start to move in jerks
8. Press the key STOP once reached the required position: the
motor stops and proves the correct storage of the
end-of-stroke with a 1/2 second movement first downwards
and then upwards.
9. Set to OFF the switch 4 of the transmitter
Switch 5: Programming of closing limit
switch of rolling shutter (louver blades)
NOTE: you must have a previously stored remote control
available and must proceed with the following points.
1. DOTTO multichannel only: press several times the key SELC of
the transmitter until displayed the channel stored
2. Position the rolling shutter at the mid-height
3. Set to ON the switch 5 of the transmitter
4. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor proves it is entering into
programming phase by moving for 1/2 second in both the
ways
5. Release the key PROG
6. Position the rolling shutter in the LOWER position desired
using the UP and DOWN buttons. To regulate it precisely,
press the PROG button when the motor is close to the limit
switch the motor will start to move in jerks
7. Press the key STOP once reached the required position: the
motor stops and then proves the correct storage of the
end-of-stroke by moving for 1/2 second first upwards and
then downwards
8. Set to OFF the switch 5 of the transmitter
Switch 6: Programming of opening position
of adjustable louver blades
NOTE: you must have a previously stored remote control
available and must proceed with the following points.
1. DOTTO multichannel only: press several times the key SELC of
the transmitter until displayed the channel stored
2. Position the rolling shutter at the mid-height
3. Set to ON the switch 6 of the transmitter
4. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor proves the correct storage
of the end-of-stroke by moving for 1/2 second in both the
ways
5. Release the key PROG
6. Using the UP and DOWN buttons, open the louver blades to
the desired position. To perform a precise adjustment press
the PROG button when the motor approaches the desired
position, the motor will begin to move jerkily
7. Press the key STOP once reached the required position: the
motor stops and then proves the correct storage of the
end-of-stroke by moving for 1/2 second first upwards and
then downwards
8. Set to OFF the switch 6 of the transmitter
To bring the rolling shutter into the opening position of
the adjustable louver blades press the STOP button for at
least 3 seconds (with the motor stationary): the louver
blades moves until it reaches the tracked position.
16
Publicidad
