Publicidad
Idiomas disponibles
Idiomas disponibles
ENGlIsh
OPERATION
WARNING: To reduce the risk of serious
personal injury, turn unit off before making any
adjustments or removing/installing attachments
or accessories. An accidental start-up can cause injury.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
LED Worklight (Fig. A)
CAUTION: When using the worklight for purposes
other than screwdriving or drilling be sure to
remove all accessories. Unused accessories could
cause injury or property damage.
CAUTION: Do not stare into the LED. Serious eye
injury could result.
When the screwdriver is activated by pulling the trigger
switch
, the LED worklight
3
The LED worklight will go off when the trigger is released.
Performing an Application (Fig. A, F)
The forward/reverse slider
the tool and also serves as a lock off button.
1. Insert and secure the appropriate bit or accessory into
the chuck
.
6
2. Grasp the screwdriver as shown in Figure F.
3. The screwdriver is turned on and off by squeezing and
releasing the trigger switch
4. To select forward rotation, release the trigger switch and
slide the forward/reverse slider
5. To select reverse rotation, slide the forward/ reverse
slider
the left.
2
NoTE: The center position of the forward/reverse
slider
locks the trigger switch
2
When changing the position of the forward/reverse
slider
, be sure the trigger switch is released.
2
NoTE: For best performance, #8, 2" and smaller fasteners
are recommended, or screw into pre-drilled holes.
NOTE: When the screwdriver is activated by squeezing
the trigger switch
, the LED worklight
3
automatically illuminate.
MAINTENANCE
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning. Your charger does not require
any maintenance apart from regular cleaning.
WARNING! To reduce the risk of serious personal
injury, turn off the tool and disconnect it from
the power source before making adjustments or
removing / installing devices or accessories. An
accidental start could cause injuries.
24
will automatically come on.
4
2
determines the direction of
.
3
2
to the right.
in the off position.
3
will
4
IMPORTANT! To ensure product Safety and
Reliability, repairs, maintenance and adjustment
(other than those listed in this manual) should be
performed by authorized service centers or other
qualified organizations, always using identical
replacement parts. Unit contains no user service able
parts inside.
CLEANING
WARNING! Blow dirt and dust from all ventilation
ducts with dry air, at least once a week. To reduce
the risk of injury, always use ansi z87.1 Approved eye
protection when performing this task.
WARNING! Never use solvents or other abrasive
chemicals to clean non-metallic parts of the tool. These
chemicals can weaken the plastic materials used in these
parts. Use a cloth dampened only with water and neutral
soap. Never allow liquid to penetrate inside the tool or
immerse any of the parts in a liquid.
ACCESSORIES
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
WARNING! The use of any accessory not recommended
for use with this tool could be hazardous.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your BLACK+DECKER
product needs replacement, or if it is of no further
use to you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
BATTERIES
BLACK+DECKER batteries can be recharged many
times. At the end of their useful life, discard
batteries with due care for our environment:
•
Run the battery down completely, then remove it from
the tool.
•
NiCd, NiMH and Li-Ion batteries are recyclable. Take
them to any authorized repair agent or a local recycling
station.
Publicidad
