Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY
Danger! Pull out the power plug before carrying out any maintenance, resetting or assembly work on the cutting-off
machine!
Assembly of the sub-frame and cooling water pump (Fig. 2-5)
• Secure the feet (1) to the water trough using the thumb screws (12).
• Place the complete tile cutter into the trough (3).
• Place the cooling water pump (13) in a suitable position in the water trough and secure it to the base of the trough with the
suction cups. The pump, cable and cooling water hose (14) must not be able to get into the cutting area.
• Fill with water until the pump (13) is completely immersed in water.
• Remove the star handle screw (11) and spacer (40).
Important: Before you lift the machine out of the trough or transport it, the cutting unit must be secured again with the star
handle screw (11) and spacer (40).
OPERATION
ON/OFF switch (Fig. 6)
• To switch on, press the "1" on the ON/OFF switch (16).
• Before you begin cutting, wait until the cutting wheel has
reached maximum speed and the cooling water pump (13) has
started supplying the cutting wheel with water.
• To switch off, press the "0" on the switch (16).
• Your machine is equipped with an overload switch (16 a). If the
machine is overloaded, the overload switch (16 a) will trigger.
After a cooling down period, the machine can be reactivated by
pressing the overload switch (16 a).
90° Cutting (Fig. 7/8)
• Loosen the star grip screw (27).
• Set the angle stop (5) to 90° and retighten the star grip screw
(27).
• Retighten the screws (28) to fasten the angle stop (5).
• Move the machine head (29) to the far end with the handle (9).
• Position the tile against the rail fence (6) on the angle stop (5).
• Switch on the tile cutting machine.
• Caution: Always wait until the cooling water has reached the
cutting wheel (2) first.
• Move the machine head (29) slowly and smoothly forward
through the tile with the handle (9).
• Switch off the tile cutting machine after completion of cutting.
45° Diagonal cut (Fig. 9)
• Set the angle stop (5) to 45°.
• Cut as described in 90° Cutting (Fig. 7/8)
45° Lengthwise cut, "jolly cut" (Fig.10)
• Loosen the star grip screw (10).
• Tilt the guide rail (7) to the left to 45° on the angle scale (17).
MAINTENANCE
• Clean off all dust and soiling from the machine at regular intervals, preferably with a cloth or a brush.
• Lubricate all moving parts at regular intervals.
• Do not use any aggressive cleaning agents to clean plastic parts.
• Clean off any soiling on the trough (3) and cooling agent pump (13) at regular intervals, otherwise the diamond cutting wheel (2)
may not be cooled as required. To empty the trough, remove the rubber stopper (36) and drain the water into a suitable vessel
(Fig. 15).
ENVIRONMENT PROTECTION
In order to prevent the machine from damage during transport, it is delivered in a sturdy packaging. Most of the packaging
materials can be recycled. Take these materials to the appropriate recycling locations. Take your unwanted machines
to your local dealer. Here they will be disposed of in an environmentally safe way.
Discarded electric appliances are recyclable and should not be discarded in the domestic waste! Please actively
support us in conserving resources and protecting the environment by returning this appliance to the collection
centres (if available).
• Retighten the star grip screw (10).
• Cut as described in 90° Cutting (Fig. 7/8)
Machining large workpieces (Fig. 11/12)
To enable you to machine large workpieces, the cutting unit
can be pivoted upwards. In this position you can machine
workpieces with a length of up to 920 mm (up to a max.
workpiece thickness of 38mm).
• Remove the screw (37) on the top for this purpose.
• The cutting until will pivot upwards automatically.
• You can now complete the required cuts as described in
sections 90° Cutting (Fig. 7/8) to 45° Lengthwise cut, "jolly
cut" (Fig.10). All that is required is slight additional pressure
downwards on the handle.
Changing the diamond cutting wheel (Fig. 13/14)
• Pull out the power plug.
• Unscrew the 3 screws (30) and remove the safety hood (8)
for the blade.
• Place the wrench (31) on the motor shaft and hold.
• Using the wrench (34), loosen the flange nut in the direction
of rotation of the cutting wheel (2).
(Caution: Left-hand screw-thread.)
• Remove the outer flange (35) and cutting wheel (2).
• Clean the mounting flange thoroughly before fitting the new
cutting wheel.
• Fit the new cutting wheel by following the above procedures
in reverse and then tighten.
Caution: Pay attention to the direction of rotation of the
cutting wheel!
• Mount the safety hood (8) for the blade again.
Publicidad
