Publicidad
TIGHTENING THE WHEEL NUTS/BOLTS
Note: When tightening wheel nuts/bolts, a torque bar (sold
separately) with the correct torque setting should be inserted
between the impact wrench and the impact socket, otherwise
the nut/bolt might be overtightened and the wheel could be
damaged.
1.
Use a 6-point impact socket that fits exactly onto the
nut/bolt you wish to tighten..
2.
Screw on the wheel nut/bolts by hand using at least 3
compelete rotations in order to prevent possible thread
damage when tighten with the impact wrench.
3.
Fit the socket fully onto the nut/bolts you wish to tighten.
Being always with the bottom wheel nut/bolt.
Reference Values for Maximum Screw/Bolt Tightening Torques
Calculated from the tensional cross-section; utilization of the yield point 90 % (with friction coefficient μtotal
= 0.12). As a controlmeasure, always check the tightening torque with a torque wrench.
Property Classes
according to DIN 267
M6
M8
M10
M12
M14
M16
M18
M20
MAINTENANCE
Make sure that the machine is not live when carrying out maintenance work on the motor. Regularly clean the machine
housing with a soft cloth, preferably after each use. Keep the ventilation slots free from dust and dirt. If the dirt does not come off
use a soft cloth moistened with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents
may damage the plastic parts.
The machine requires no additional lubrication.
ENVIRONMENT PROTECTION
In order to prevent the machine from damage during transport, it is delivered in a sturdy packaging. Most of the
packaging materials can be recycled. Take these materials to the appropriate recycling locations. Take your
unwanted machines to your local dealer. Here they will be disposed of in an environmentally safe way.
Discarded electric appliances are recyclable and should not be discarded in the domestic waste! Please actively
support us in conserving resources and protecting the environment by returning this appliance to the collection
centres (if available).
We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents:
EN62841-1:2015; EN62841-2-2:2014;EN55014-1:2006/A2:2011;EN55014-2:2015; EN61000-3-2:2014;EN61000-3-3:2013; in
accordance with the regulations 2006/42/ЕEС, 2014/30/ЕEС.
NOISE/VIBRATION Measured in accordance with EN62841 the sound pressure level of this tool is <100 dB(A) and the sound
power level is <111dB(A) .
Standard Screws/Bolts
3.6
4.6
5.6
2.71
3.61
4.52
6.57
8.7
11
13
17.5
22
22.6
30
37.6
36
48
60
55
73
92
75
101
126
107
143
178
DECLARATION OF CONFORMITY
4.
Grip the impact wrench securely using one hand to
grip the front of the machine and the other hand
holding the handle.
5.
Pull the lower part of the power trigger for colockwise
rotation (tighten).
6.
Lower the jack so that all wheels are touching the
ground.
Warning: Use a torque wrench to check that the wheels
are fasten to the recommended torque setting before
using the car after changing its wheels.
Note: Tighten the wheel nuts/bolts in the correct order.
The order is by the diagonal orders.
4.8
6.6
5.8
4.8
5.42
6.02
7.22
11.6
13.1
14.6
17.5
23
26
29
40
45
50
65
72
79
98
110
122
147
135
151
168
202
190
214
238
286
High-strength Bolts
6.8
6.9
8.8
10.9
8.13
9.7
13.6
19.7
23
35
39
47
60
67
80
95
107
130
165
196
227
270
320
385
12.9
16.2
33
39
65
78
113
135
180
215
275
330
380
450
540
635
Publicidad
