XPG CYBERCORE II PLATINUM Serie Guia De Inicio Rapido página 5

CONGRATULATIONS ON THE PURCHASE OF YOUR NEW
XPG CYBERCORE II PLATINUM SERIES POWER SUPPLIES
XPG CYBERCORE II PLATINUM Series power supplies are created for silence with extreme
power performance, designed with a 120mm XPG VENTO PRO 120 PWM cooling fan
featuring extremely low RPM fan control circuit design allows the fan to operate
efficiently and silently. 80 PLUS PLATINUM rated efficiency ensures low-cost operation,
and its fully modular cable set provides user convenience and easy to build.
XPG CYBERCORE II PLATINUM uses high quality 105°C Japanese capacitors throughout
and is a great choice for a high performance PC.
SAFETY AND PROTECTION
The main outputs will be latched off when each protection is triggered. The main
output can be reset by cycling the DC remote on/off or AC power. +5Vsb output is auto
recovery when fault condition is removed.
CYBERCORE II PLATINUM SERIES
* XPG CYBERCORE II PLATINUM Power Supply Unit
* AC Power Cord x 1
* DC Modular cable pack
* DC Modular cable storage bag x 1
* Cable Ties x 10
* Thumb Screw x 4
* User Manual
INSTALLING YOUR NEW XPG CYBERCORE II POWER SUPPLY
1. Please turn off AC power switch if you are swapping the power supply.
2. Please install your XPG Power Supply in the correct area
3. Please use a screwdriver to install the power supply
4. Please connect the 18+10pin Modular cable connector to the PSU modular socket
5. Please connect the 20+4 pin MB connector to the 24pin socket on the MB
6. Please connect the CPU 8pin Modular cable connector to the PSU modular CPU power
7. Please connect the 8 or 4 pin CPU connector to the CPU power socket on the MB if
required.
8. Please connect the PCI-E 8pin or 12VHPWR (12 + 4pin) Modular cable connector to the
PSU modular VGA power socket if required.
9. Please connect PCI-E 2.0 (6 + 2pin) or 12VHPWR (12 + 4pin) Modular cable connector to
the socket on the VGA card if required.
10. Please connect the 6pin Modular cable connector to the PSU modular SATA or Molex
power socket if required.
11. Please connect the SATA or Molex Connectors to all the peripherals if required.
12. Please turn on the AC power switch if you have finished your system installation.
EN
07
TROUBLESHOOTING
If your system does not turn on after installing the power supply, please follow the
troubleshooting guide listed below:
1. Please make sure the AC main power cord is connected to your PC correctly.
2. Please make sure the AC source is switched On
3. Please make sure the AC On/Off switch on the back panel of the power supply unit in the
"I" (On) position.
4. Please make sure the MB & CPU Power Socket & connectors are connected correctly on
the Motherboard.
5. If you still have problem turning on your PC, please contact ADATA Tech Support, Service
Center or your local dealer.
DURATION OF WARRANTY
ADATA Technology Co., Ltd. provides a 10 years warranty period for this product unless
regional laws and regulations state otherwise.
LIMITATION OF WARRANTY
This limited warranty covers only repairs or replacements of products manufactured by
ADATA Technology Co. Ltd. and its authorized partners.
Please note that ADATA is responsible for providing free repairs except for the following
reasons:
1. The warranty label is altered, damaged or missing.
2. Product serial number does not conform to our original system.
3. Products purchased from an unauthorized agent.
4. Damage caused by natural calamity
5. Any abuse outside the intended product operation.
ONLINE CUSTOMER SERVICE
For frequently asked questions, additional information and service instruction please visit
the product page at www.xpg.com
IMPORTANT SAFETY INFORMATION
1. NEVER, under any circumstances, open the power supply unit or attempt to repair the power
supply. This is extremely dangerous due to the high voltage inside.
2. DO NOT insert any objects into the fan grill or the ventilation area of the power supply unit.
3.
DO NOT place any objects in front of the fan or the ventilation area of the power supply unit
that may obstruct or restrict the airflow.
4. USE ONLY the modular cables bundled with the power supply unit. DO NOT use any third
party cables or extension cables with this unit.
5. Avoid dust, humidity, and temperature extremes. Do not place the power supply unit in any
area where it may become wet.
6.
The power supply unit is for integration into a computer, and not intended for external or
outdoor usage.
7. Failure to comply with any manufacturer instructions and/or any of these safety instructions
will immediately void all warranties and guarantees.
08