Maintenance; Sharpening The Saw Chain; Cleaning And Storage; Information For Environmental Protection/ Disposal - IKRA EAS 750F Instrucciones De Manejo

Motosierra eléctrica telescópica de poda
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 56

9. Maintenance

9.1 Replacing the saw chain and guide bar
The guide bar must be replaced if the guide
• groove of the guide bar is worn out.
• the spur wheel in the guide bar is damaged or worn out.
For this purpose, proceed as described in the chapter
"Assembly of the guide bar and saw chain"!
9.2 Checking the automatic chain lubrication
Regularly check the functionality of the automatic chain
lubrication in order to prevent overheating and the
subsequent damage to the guide bar and saw chain
associated with it. For this purpose, align the guide bar
tip against a smooth surface (board, cut-in of a tree)
and allow the chainsaw to run. If an increasing amount
of oil appears, the automatic chain lubrication functions
properly. If no clear trace of oil appears, please read the
appropriate information in the chapter "Fault remedy"!
If this information does not help, please contact our cus-
tomer service or a similarly qualified workshop.
Attention! Do not touch the surface during the
process. Maintain a sufficient safety clearance
(approx. 20 cm).

9.3 Sharpening the saw chain

Effective work with the chainsaw is only possible if the
saw chain is in good condition and sharp. This also
reduces the danger of a kickback. The saw chain can
be resharpened by a specialty dealer. Do not attempt to
sharpen the saw chain yourself if you do not have a suit-
able tool and the necessary experience.

10. Cleaning and storage

• Regularly clean the tensioning mechanism by blowing
compressed air onto or cleaning it with a brush. Do
not use any tools for the cleaning.
• Keep oil away from the handle in order to ensure a
secure hold.
• Clean the machine as necessary with a damp cloth
and a mild cleanser, if appropriate.
• If the chainsaw is not used for an extended period of
time, remove the chain oil from the tank. Briefly place
the chainsaw and the guide bar in an oil bath and then
wrap it in oil paper.
Attention!
• Always replace the protective cover for transport or
storage of the chainsaw.
• Pull out the mains plug before cleaning.
• Never immerse the machine in water or other liquids.
• Store the chainsaw in a safe and dry place and out of
the reach of children.
11. Information for environmental protection/
disposal
Dispose of the machine properly after it is worn out. Dis-
GB | Operating Instructions
connect the mains cable in order to prevent misuse. Do
not dispose of the machine with the household waste. In
the interest of environmental protection, take it to a col-
lection point for electric machines. Your responsible local
authority can provide you with addresses and operating
times. Also take the packaging materials and worn out
accessories to the appropriate collection points.
In accordance with European Directive 2012/19/EU on
waste electrical and electronic equipment and its im-
plementation in national law, waste electric tools must
be collected separately for environmentally-compatible
re-use.
Recycling alternative to the return invitation:
Instead of returning the electric equipment, the owner is
alternatively obligated to take part in the proper recycling
in the case of relinquishment of ownership. The waste
equipment can also be taken to a collection facility which
disposes of it in the sense of the national recycling man-
agement and waste acts. This does not pertain to the
accessory parts and auxiliary equipment without electri-
cal components accompanying the waste equipment.

12. Repair Service

Repairs to electric power tools should only be carried out
by specialist electrical personnel.
Always keep the original packaging for a possibly re-
quired shipping of the tool.

13. Ordering spare parts

If you need accessories or spare parts, please contact our
Service department.
When working with this tool, do not use any accessory
parts other than those recommended by our company.
Otherwise the operator or others in the vicinity could suffer
serious injuries, or the tool could be damaged.
The following information should be provided when
ordering spare parts:
• Type of machine
• Item number of the machine

14. Warranty

For this electric tool, the company provides the end
user - independently from the retailer's obligations re-
sulting from the purchasing contract - with the following
warranties:
The warranty period is 24 months beginning from the
hand-over of the device which has to be proved by
the original purchasing document. For commercial use
and use for rent, the warranty period is reduced to 12
months. Wearing parts and defects caused by the use
of non fitting accessories, repair with parts that are not
original parts of the manufacturer, use of force, strokes
and breaking as well as mischievous overloading of the
10
Only for EU countries
Do not discard electric tools in the house-
hold waste!

Publicidad

Tabla de contenido
loading

Tabla de contenido