Initial Setup; Performing An Automatic Channel Search - Peaq PTV462403 Manual De Usuario

Chapter 3

Initial setup

Initial setup involves selecting all the settings
required to be able to search for and store all the
analogue and digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specified hereafter.
Note: If the channel search retrieved only the
analogue channels it could be caused by poor
broadcasting and therefore is not covered
by manufacturer warranty. Manufacturers
cannot be held responsible for lack of or poor
broadcasting in some areas.
The first time you switch the set on, the Initial setup
wizard opens, which guides you through the initial
setup process. (Refer to Figure 1.)
1. Press ▲/▼ to select your language, then press
OK/► to enter the next step.
2. Press ▲/▼ to select your country, then press
OK/► to enter the next step.
Note: If you select France, you will have to enter
the Password setting menu here in order
to set a password. Use the alphanumeric
buttons to enter a four-digit number for
your password. (0000 is too simple to be
set as your password.) Re-enter the same
code to confirm the password. After that,
you will enter the next step automatically.
(In this step, you can only press ◄ to
return to the previous step.)
3. Press ▲/▼ to select your tuner mode
Antenna or Cable or
Satellite option may not be available for certain
models.)
- Select Antenna.
OK/► to enter.
Digital & Analogue, Digital or
Analogue, then press OK/►.
▲/▼ to select Scan, then press OK/►
to start the automatic search for all DVB-T
digital and/or analogue channels.
Cable.
- Select
OK/► to enter.
Digital & Analogue, Digital or
Analogue, then press OK/►.
▲/▼ to select Scan, then press OK/►
to directly start your initial setup or enter
below step.
Full if available to search for and
store all DVB-C digital and analogue
channels.
mode if available (for example, Advanced ),
then configure the correct cable information
as described below. Use the alphanumeric
buttons to adjust the values for frequency,
4. Before starting the scanning, you can also select
5. During the setup, you can follow the hints
6. Once the automatic search ends, the set enters
7. - In this step, you can press OK to exit the initial
Satellite. (Note:

Performing an automatic channel search

This section describes how to search and store
channels automatically. Instructions are for both
analogue and digital channels.
1. Press MENU on the remote control and select
2. Press MENU to return to Setup, press ▲/▼ to
3. Press ▲/▼ to select Tuner mode, then press
EN 8
Installing channels
symbol rate and network ID; use ◄/► to
select a modulation mode.
OK to start initial setup relating to all
DVB-C digital and analogue channels.
- Select Satellite.
OK/► to enter.
▲/▼ to select Scan, then press OK/►
to enter the next step to configure proper
information relating to satellite and antenna.
OK to start initial setup relating to all
satellite channels.
Note: To prevent the channel setup process from
being interrupted, wait for the message
indicating that the setup is complete.
Skip scan to skip the initial setup process.
available at the bottom of the screen to return to
the previous step by pressing ◄. Or press EXIT
to exit or interrupt the search halfway.
the next step automatically. Press ▲/▼ to select
your location Shop or Home. Press OK/► to
confirm your selection and enter the last step.
setup. The channels are arranged in a preset
order. If you wish to skip channels, modify the
preset order or rename channels, select
Setup > Organiser and press OK/► to enter.
- In this step, you can also press ◄ to return to
the previous step.
Setup > Language > Menu language. Press
◄/► to select your desired menu language.
select Country, then press ◄/► to select your
country. The TV installs and arranges channels
according to your country.
◄/► to select Antenna,
Satellite. (Note: Satellite option may not be
available for certain models.)
- Select Antenna.
▲/▼ to select Channel install, and
press OK/► to enter.
Automatic search (Refer to Figure 2.),
then press OK/► to display Automatic
search.
OK to skip the country selection and
use ◄/► to reselect
enter the next step. Or
your country, then press OK to enter.
Cable or