Time Detection; Assigning A Channel Decoder; Diagnostics On Digital Tv Channels; Time Shift - Peaq PTV462403 Manual De Usuario

Deregister your TV:
If you wish to deregister your TV,
MENU on the remote control.
Options > DivX(R) deregistration.
OK/► and a message will guide you.
DivX®, DivX Certified®, DivX Plus® HD and
associated logos are trademarks of Rovi Corporation
or its subsidiaries and are used under license.

Time detection

You can detect the time from digital channels using
the following operations.
1. Press MENU on the remote control and
select Options >Timer > Clock > Auto
synchronization.
2. Press ◄/► to select On.

Assigning a channel decoder

Decoders that decode analogue channels can be
connected to the AV connector. Assign the TV
channel as a channel to be decoded. Then assign the
connection where the decoder is connected.
1. Press MENU on the remote control and select
Setup > Decode.
2. Press OK/► to enter the list.
3. Press ▲/▼ to select the channel to decode.
4. Press OK to select or unselect the channel.
5. Press MENU to return to the previous menu.

Diagnostics on digital TV channels

1. Press MENU on the remote control and select
Setup > Diagnostics.
2. Press OK/► to display some signal information
on the current digital channel, such as signal
strength, frequency, etc.

Time shift

Allows you to record the TV programme so that you
will not miss the favourite part even if you go out.
Before you use the function, connect a USB device
to the TV first. For the first time, you should do the
disk setup for the USB device.
Note: Feature is available only in selected products
and, due to specific TV network limitations
and country technical requirements, might not
be available in product or place of installation.
Feature might be also blocked by TV network
due to copyright protection (HD content,
recording protection). Please use OPTION
on the remote control to check if feature is
available in your product.
1. Press MENU on the remote control and select
Setup > Time shift.
2. Press ◄/► to select On to switch on the time
shift function, then press EXIT to close the menu.
3. Press OPTION on the remote control and select
Time shift, then press OK to confirm.
4. Follow the directions on the screen to do the
setup.
5. After the disk setup is done, press OPTION and
select Time shift.
6. Press OK to display the time shift menu.
- Press the red button to pause the picture and
begin the time shift.
- Press the red button to play the recorded part.
- When the time shift menu disappears and
only the timing of the time shift remains on the
screen, you can press the red button or OK to
access the time shift menu.
- Press the green button to fast backward or the
yellow button to fast forward.
- Press the blue button to quit the time shift function.
Notes:
- Before you connect the USB device to the TV,
make sure you have backed up the data in the
device to avoid the loss of your important data
due to unforeseen malfunction.
- We recommend you use a USB device with free
capacity above 1GB and disk speed faster than
5.0MB/sec.
- The bigger the file size for time shift, the longer
the recording time.
- If you change the channel in time shift mode, a
message prompts you to select Yes or No. You
can select Yes to exit the time shift function and
execute the channel change.

Reset shop

Allows you to reset the TV to factory default settings.
1. Press MENU on the remote control and select
Setup, then press OK to confirm.
2. Select Reset shop and press OK/► to enter.
3. Use the alphanumeric buttons to enter the
password.
4. Press ◄/► to select OK and press OK to confirm.
5. The Initial setup menu appears. Follow the
related instructions.

Customising the input settings

You can configure your TV according to the
equipment you connect to it.
1. Press MENU on the remote control and select
Setup > Input settings.
2. Press OK/► to enter Input settings.
3. Press ▲/▼ to select a connector your equipment
is connected to.
4. Press ◄/► to select the type of apparatus
attached to this connector.
EN 14
Using more of your TV