Publicidad
Idiomas disponibles
Idiomas disponibles
ENGlIsh
3. To remove the wheel, reverse the above procedure.
NOTICE: To reduce the risk of damage to the tool,
properly seat the wheel hub before turning the tool on.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Installing and Removing the Battery Pack
(Fig. K)
NOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
12
button
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. L)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
13
handle
and the other hand on the auxilliary handle
shown in Figure L.
On/Off Switch (Fig. M)
WARNING: Do not switch the tool off while
under load.
CAUTION: Hold the auxiliary handle and body of the
tool firmly to maintain control of the tool at start up
and during use and until the wheel or accessory stops
rotating. Make sure the wheel has come to a complete
stop be fore laying the tool down.
CAUTION: Allow the tool to reach full speed before
touching tool to the work surface. Lift the tool from the
work surface before turning the tool off.
•
To start the grinder, press the lock‑off button
squeeze the on/off switch
•
For continuous operation, press the lock‑on button
and release the on/off switch.
•
To switch the tool off, release the on/off switch. To switch
the tool off in continuous operation, press the on/off
switch once more and release it.
Spindle Lock (Fig. N)
3
The spindle lock button
from rotating when installing or removing wheels. Operate
the spindle lock only when the tool is turned off, the battery
is removed and has come to a complete stop.
42
7
into the tool handle, align the
2
1
.
is provided to prevent the spindle
NOTICE: To reduce the risk of damage to the tool, do
not engage the spindle lock while the tool is operating.
Damage to the tool will result and attached accessory
may spin off possibly resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate the
spindle further.
Surface Grinding, Sanding and Wire
Brushing (Fig. O)
CAUTION: Always use the correct guard per the
instructions in this manual.
To perform work on the surface of a workpiece:
1. Allow the tool to reach full speed before touching the
tool to the work surface.
2. Apply minimum pressure to the work surface, allowing
the tool to operate at high speed. Material removal rate is
greatest when the tool operates at high speed.
3. Maintain an appropriate angle between the tool
and work surface. Refer to the chart according to
particular function.
Function
Grinding
Sanding with Flap Disc
Sanding with Backing Pad
Wire Brushing
4. Maintain contact between the edge of the wheel and the
work surface.
-
If grinding, sanding with flap discs or wire brushing
5
, as
move the tool continuously in a forward and back
motion to avoid creating gouges in the work surface.
-
If sanding with a backing pad, move the tool
constantly in a straight line to prevent burning and
swirling of work surface.
NOTE: Allowing the tool to rest on the work surface without
moving will damage the workpiece.
5. Remove the tool from work surface before turning tool
off. Allow the tool to stop rotating before laying it down.
CAUTION: Use extra care when working over an
edge, as a sudden sharp movement of grinder may
be experienced.
Precautions To Take When Working on a
and then
Painted Workpiece
1. Sanding or wire brushing of lead based paint is NOT
2
RECOMMENDED due to the difficulty of controlling
the contaminated dust. The greatest danger of lead
poisoning is to children and pregnant women.
2. Since it is difficult to identify whether or not a paint
contains lead without a chemical analysis, we
recommend the following precautions when sanding
any paint:
personal safety
1. No children or pregnant women should enter the work
area where the paint sanding or wire brushing is being
done until all clean up is completed.
Angle
20˚‑30˚
5˚‑10˚
5˚‑15˚
5˚‑10˚
Publicidad
