Aritech VE700AM Serie Manual De Instrucciones página 11

Regulatory information
Manufacturer PLACED ON THE MARKET BY:
Carrier Fire & Security Americas Corporation Inc.
13995 Pasteur Blvd
Palm Beach Gardens, FL 33418, USA
AUTHORIZED EU REPRESENTATIVE:
Carrier Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings THESE PRODUCTS ARE INTENDED FOR SALE
and disclaimers TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. CARRIER FIRE &
SECURITY CANNOT PROVIDE ANY
ASSURANCE THAT ANY PERSON OR ENTITY
BUYING ITS PRODUCTS, INCLUDING ANY
"AUTHORIZED DEALER" OR "AUTHORIZED
RESELLER", IS PROPERLY TRAINED OR
EXPERIENCED TO CORRECTLY INSTALL FIRE
AND SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/ or scan the QR code.
Certification
ICES-003 This Class B digital apparatus complies with
Canadian ICES-003.
FCC This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an output on a
circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Product may contain substances that are also
REACH
Candidate List substances in a concentration
above 0.1% w/w, per the most recently published
Candidate List found at ECHA Web site.
Safe use information can be found at
https://firesecurityproducts.com/en/content/intrusi
on-intro
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
recyclethis.info
P/N 149973999-3-ML • REV M • ISS 10JUN21
Product Please consult the following weblink to retrieve
documentation the electronic version of the product
documentation.
This link will guide you to the EMEA regional
contact page. On this page you can request your
login to the secured webportal where all manuals
are stored.
https://firesecurityproducts.com/en/contact
Contact information
firesecurityproducts.com or www.aritech.com
DA: Installationsvejledning
Introduktion
VE735AM og VE736AM er PIR-AM-bevægelsesfølere. Som
har en patenteret og verificeret PIR-teknologi med flerkanals
anti-mask.
ADVARSEL! Udstyret er ikke jordet. Ethvert ekstern
kredsløb, der er tilsluttet udstyreret, skal være
placeret i den samme bygning og tilsluttes en
beskyttende jordleder.
Trådisolering af kabler, der er tilsluttet udstyret, skal være
i overensstemmelse med IEC 60332-1-2 og IEC 60332-1-3
eller IEC 60332-2-2, afhængig af ledningens tværsnit, eller
IEC TS 60695-11-21, uanset af tværsnitsarealet. Alternativ
skal sådanne ledninger være i overensstemmelse med
UL 2556 VW-1.
Installationsvejledning
Teknologien i denne detektor er modstandsdygtig over for
falske alarmer. Ikke desto mindre skal du undgå mulige
årsager til ustabilitet, f.eks.:
• Direkte sollys på detektoren
•
Varmekilder inden for synsvidde
• Kraftig træk på detektoren
•
Store dyr inden for synsvidde
•
Genstande inden for 50 cm fra anti-mask-detektoren (AM)
•
Blokering af detektorens synsfelt med store genstande
som f.eks. møbler
•
Montering af to detektorer, der vender mod hinanden, i en
afstand af mindre end 50 cm
Monter detektoren således at en forventet bevægelse af en
indbrudstyv, vil være på tværs af detektorens overvågningsfelt
(se eksempel på Figur 21, punkt 1). Dette er retningen som
best detekteres af PIR detektoren.
Montering af detektoren
Løft dækpladen af, og fjern skruen (Figur 1).
1.
Åbn forsigtigt detektoren med en skruetrækker (Figur 2).
2.
3. Udtag den indre del (Figur 3).
Gør soklen fast til væggen mellem 1,8 m og 3,0 m fra
4.
gulvet. Til plan montering, bruges minimum to skruer
(DIN 7998), mindst én i position A og én i position B.
11 / 62