Pyronix Me Q 12 Guia De Inicio Rapido

A1
HORIZONTAL COVERAGE
12M
10M
Horizontal Coverage
at Maximum Range
Setting
8M
6M
4M
2M
A2
2.4M
8ft
2M 4M 6M
LED ON
LED OFF
PCB at Maximum
VERTICAL COVERAGE
Range Setting
T T N / C - +
2.4M
8ft
2M 4M 6M
PCB at Minimum
Range Setting o
VOLUMETRIC 90
LED ON
LENS 2
LED OFF
-
T T N / C +
-
D1
Pulse
Count 1.
Pulse
Count 2.
(Factory
Default)
1
Pulse
Count 3.
0.3 - 3.0 m/s
Control Panel
E2
E1 ZONE
TAMP
ZONAS
24HR
ZONES
E3
PIR
9 - 16Vdc
15mA
12V
60V
@12Vdc
50mA
50mA
B1
Mark wall for fixing
positions.
Choose 2 suitable wall
fixing knockouts.
B3
B2
Mounting and
Cable entry.
Cable = 5mm
LED ON
LED OFF
T T N / C - +
Replace Printed
8M 10M 12M
circuit board.
= 80g (2.8 oz) without bracket
Kg
C1
3mm
(0.12")
8M 10M 12M
108 ZONE EDGES
3 PLAINS
60mm (2.36")
PULSE COUNT
SELECT
LED ON
LED OFF
N N C C T T T T + + - -
2
3
T T
T T
LED ON
LED OFF
This product is sold subject to our standard
T T N C / - +
warranty conditions and is warranted
against defects in workmanship for a period
ALARM
NORMAL
In the interest of continuing improvement
of quality, customer care and design, Pyronix Ltd
reserve the right to amend specifications
NORMAL ALARM
INSTALLATION
Drill fixing
holes.
1. Remove case lid by unscrewing fixing screw
and remove the PCB.
Use 5.0mm
(Do not touch Pyro sensor
drill bit.
2. Choose suitable wall fixing holes.
3. Mark wall for fixing positions (Do not route wires near mains
cabling, avoid vibrating surfaces, and only use solid wall).
4. Drill fixing holes.
5. Fix case to wall.
6. Replace PCB (Do not touch Pyro sensor
7. Refit lid to case and fasten.
POTENTIAL FALSE ALARM HAZARDS
1. Direct sun light on detector may cause false alarms.
2. False Alarms may be caused by pets and animals.
3. Do not mount detectors near heaters.
4. Draughts from open windows may cause false alarms.
B5
Cable Entry
DIAGRAMS
Knockouts.
Horizontal Coverage Pattern.
A1
B4
PIR Range Adjustment. Mounting Height = 1.8 to 2.4m
A2
(Height adjustment will effect PIR range)
Wall fixing Knockouts.
B1
Wall Mounting
B2
Ceiling mounting.(Mounting is optional with EB2 bracket, not supplied)
B3
Case lid screw fitting.
B4
Cable Entry Knockouts.
B5
Measurements and weight (80g) without bracket.
C1
Pulse count 1,2,3 (Increases the detection time before an alarm
D1
condition is generated)
42mm (1.65")
LED disabled when link pin removed.
D2
Pyro Sensor (Do not touch)
D3
D3 Wiring to control panel.
E1
Tamper Operation
E2
Normal = Cover closed
Alarm = Cover open
PYRO SENSOR
SPECIFICATIONS (QUICK REFERENCE)
Model:
D2
ALARM LED
Colour:
Casing:
Detection method:
Sensitivity:
Disable Enable
Temperature Compensation:
Detection Range:
Detection Zones:
Detection speed:
WARRANTY Operating Voltage:
Quiescent Current:
Relay Output:
of five years. Mounting Height:
Tamper Switch:
Storage Temp:
Operating Temp:
without giving prior notice
Accessories:
Emissions:
Immunity:
GB
,
B4
D3 )
B1
B2
).
D3
B4
Relay Contacts
E3
Normal = No movement
Alarm = Intruder detected
MEQ 12
White
3mm ABS , 0.4mm HDPE in Lens area.
Low noise Quad Element Pyroelectric sensor
Analogue Pulse Count 1,2,3
Advanced
12m
Lens No 2 = 108 zone edges .
0.3 - 3 .0 m/s
9-16 VDC
15 mA at 12V
SELV limits; 60Vdc, 50mA (42.4Vac peak)
1.8m - 2.4m
12V 50mA
-40 C / 80 C (-40 F / 176 F )
-30 C / 70 C (-22 F / 158 F )
EB2/PB2 Mounting bracket. (Not Supplied)
EN55022 Class B
To new European Standard
EN50130-4
Me Q 12 Me Q 12
Pyronix Limited
Pyronix House
Braithwell Way
Hellaby, Rotherham
S66 8QY, ENGLAND
Customer Support:
+44(0)845 6434 999 (local rate)
or +44(0)1709 535225
Hours: Mon to Fri, 8:00am till 6:30pm
Email: customer.support@pyronix.com
Website: www.pyronix.com
R
PYRONIX
0C03
This product is approved for use in the
Residential, Commercial and Light Industrial Environment.
TS50131-2-2
EN50131-1
2
PD6662:2004
Security Grade 2
Environmental Class 2
This product complies with TS50131-2-2. at security grade 2,
environmental class 2.
UK = Suitable for use with systems installed to PD6662:2004 (AMD)
EXPORT = Suitable for use with systems installed to EN50131-1
RINS379-5