Sthor 78157 Manual De Instrucciones página 11

GB
Do not expose electric tools to precipitation or humidity. Water and humidity which gets into the electric tool increases the risk of
an electric shock.
Do not overload the power supply cable. Do not use the power supply cable in order to carry the tool or to connect and
disconnect the plug from the mains socket. Avoid contact of the power supply cable with heat, oils, sharp tools and moving
elements. Damage to the power supply cable increases the risk of an electric shock.
In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside closed
areas. Using a correct extension cord permits to reduce the risk of an electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RDC) protected supply. Use of an
RCD reduces the risk of electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are tired or
under effects of medicines or alcohol. Even a moment's inattention during work may lead to serious injuries.
Always use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks,
protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries.
Avoid accidental activation of the tool. Make sure the switch is in the OFF position, before you connect the tool to the mains.
Holding the tool with a finger on the switch or connecting an electric tool when the switch is in the ON position may lead to serious
injuries.
Before you turn an electric tool on remove all the spanners and other tools, which have been used for adjustments. A spanner
left on rotating elements of the tool may lead to serious injuries.
Keep your balance. Maintain an appropriate position. It will permit to control the electric tool in case of unpredicted situations during
its operation.
Use protective clothes. Do not wear loose clothes or jewellery. Keep your hair, clothes and gloves away from moving elements
of the electric tool. Loose clothes, jewellery or long hair may get caught on moving elements of the tool.
Use dust extractors or dust containers, if the tool is equipped with any. Make sure they are properly connected. Using of dust
extractors permits to reduce the risk of serious injuries.
Caution when using a power tool.
Before inserting a battery pack make sure that the switch stays in "OFF" position. Inserting a battery pack into a power tool, when
the switch is in "ON" position may cause accidents.
Use only chargers recommended by the manufacturer. Using a charger designed for only one type of battery pack, to charge other
types of battery pack may be a cause of fire.
Use power tools only with battery pack specified by the manufacturer. Use of other battery pack may be a cause of injuries or fire.
When the battery pack is not used, it should be stored away from metal objects, such as paper clips, coins, nails, bolts or
other small metal elements, that may short the terminals. Shorting terminals of a battery may cause burns or fire.
In adverse conditions, a liquid may escape from a battery; avoid any contact with this liquid. In case of accidental contact
with a liquid, rinse with water. If a liquid gets into your eyes, please seek medical advice. A liquid escaping from a battery may
cause irritations or burns.
Repairs
The tool may be repaired only by authorised service centres, which must use solely original spare parts. It will guarantee a
proper level of safety of operation of the electric tool.
SPECIAL SAFETY CONDITIONS
Always assume that the tool contains fasteners. Gripping the tool without proper care may result in unexpected firing of fastener
and injury.
Do not aim the tool at yourself or at other persons that stay nearby. Unexpected pressing of trigger will cause firing of fastener
causing an injury.
Do not start the tool until the tool is securely placed on a work piece. If the tool has no contact with the work piece, a fastener
may rebound from the target point.
Disconnect the tool from power supply in case the fastener jams in the tool. When removing the fastener jammed, the tool must not be
accidentally activated if it is on.
Be cautious when removing the fastener jammed. The mechanism may be squeezed and the fastener may be released with suffi-
cient force when removing the jammed element.
Do not use the tool for mounting electric cables. The tool has not been designed for installation of electric cables and may damage
the insulation of electric cables resulting in hazard of electric shock and fire.
PREPARATION TO WORK
Note! All operations described in this chapter should be carried out with power supply off. Make sure that the switch remains in "OFF
- O" position [V].
11
O R I G I N A L I N S T R U C T I O N S