Porter Cable 342 Manual De Instrucciones

1/4 Sheet Sander
Ponceuses à 1/4 feuille
Lijadoras de 1/4 de hoja
Instruction manual
Manuel d'instructions
Manual de'instrucciones
www.deltaportercable.com
INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.
LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
Part No. A28837 10-09-08
DEFINITIONS - SAFETY GUIDELINES
indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
indicates a potentially haz ard ous situation which, if not
avoided, may result in minor or mod er ate injury.
used without the safety alert symbol indicates potentially haz-
ardous situation which, if not avoided, may result in property damage.
To reduce the risk of injury, read the instruction manual.
GENErAL POwEr TOOL SAFETY wArNINGS
read all safety warnings and instructions Failure to follow the
warnings and instructions may result in electric shock, fire and/or
serious injury.
Save all warningS and inStructionS
for future reference
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) wOrk ArEA SAFETY
a) keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
2) ELEcTrIcAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) when operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit
interrupter (GFcI) protected supply. Use of a GFCI reduces the risk of electric shock.
3) PErSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before connect-
ing to power source and/or battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools that have the switch on invites
accidents.
d) remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. keep proper footing and balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in mov-
ing parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
related hazards.
4) POwEr TOOL USE AND cArE
a) Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool
before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are dan-
gerous in the hands of untrained users.
e) Maintain power tools. check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool's operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
f) keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these instructions
taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a hazardous situation.
5) SErvIcE
a) Have your power tool serviced by a qualified repair person using only identical replace-
ment parts. This will ensure that the safety of the power tool is maintained.
• Hold power tools by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock the operator.
• Do not sand metal of any kind with your sander. Sparks may be generated by sanding screws,
nails or other metals which may ignite dust particles.
• Do not wet sand with this sander. Liquids may enter the motor housing and cause electric
shock.
• Empty dust collection system frequently, especially when sanding resin coated surfaces
such as polyurethane, varnish, shellac, etc. Dispose of coated dust particles according to
the finish manufacturer's guidelines, or place in a metal can with a tight fitting metal lid. Remove
coated dust particles from the premises daily. The accumulation of fine sanding dust particles may
self ignite and cause fire.
• Do not operate this tool for long periods of time. Vibration caused by the operating action of
this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra
cushion, take frequent rest periods, and limit daily time of use.
• Sanding of lead-based paint, chemically pressure treated lumber or other materials that
may contain carcinogens is not recommended. Sanding of these materials should only be
performed by a professional.
• clean out your tool often, especially after heavy use. Dust and grit containing metal particles
often accumulate on interior surfaces and could create a risk of serious injury, electric shock or
electrocution. ALWAyS disconnect the sander from the power source before cleaning. ALWAyS
WEAR SAFETy GLASSES that conform to ANSI Z87.1.
• ALwAYS disconnect tool from the power source before changing abrasive belts or sheets.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
ExTENSION cOrD
An extension cord must have adequate wire size (AwG or American wire Gauge) for safety.
The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge
has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in
loss of power and overheating. When using more than one extension to make up the total length,
be sure each individual extension contains at least the minimum wire size. The following table
shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt,
use the next heavier gauge. The smaller the gauge number, the heavier the cord.
342
Copyright © 2008 Porter-Cable
activities contains chemicals known to the State of California to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
•
•
•
your risk from exposure to these chemicals varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area with approved safety
equipment, such as dust masks that are specially designed to filter out microscopic particles.
other construction activities. Wear protective clothing and wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful
chemicals.
manent respiratory damage or other injury. Always use NIOSH/OSHA/MSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
during use. Under some conditions and duration of use, noise from this product may contribute to
hearing loss.
glasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAyS
WEAR CERTIFIED SAFETy EQUIPMENT:
•
•
•
SYMBOLS
The label on your tool may include the following symbols. The symbols and their definitions are as
follows:
V ....................... volts
Hz .................... hertz
min ................... minutes
..................... Class I Construction
.........................
.................... Class II Construction
.........................
.../min .............. per minute
OPM ................ orbits per minute
1. Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the con-
taminated dust. The greatest danger of lead poisoning is to children and pregnant women.
2. Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we
recommend the following precautions when sanding any paint:
PErSONAL SAFETY
1. No children or pregnant women should enter the work area where the paint sanding is being
done until all clean up is completed.
2. A dust mask or respirator should be worn by all persons entering the work area. The filter should
be replaced daily or whenever the wearer has difficulty breathing. See your local hardware store
for the proper NIOSH approved dust mask.
3. NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting
contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking or
smoking. Articles of food, drink, or smoking should not be left in the work area where dust would
settle on them.
ENvIrONMENTAL SAFETY
1. Paint should be removed in such a manner as to minimize the amount of dust generated.
2. Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mil thickness.
3. Sanding should be done in a manner to reduce tracking of paint dust outside the work area.
cLEANING AND DISPOSAL
1. All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration
of the sanding project. Vacuum filter bags should be changed frequently.
2. Plastic drop cloths should be gathered up and disposed of along with any dust chips or other
removal debris. They should be placed in sealed refuse receptacles and disposed of through
regular trash pick-up procedures. During clean up, children and pregnant women should be kept
away from the immediate work area.
ADDITIONAL SPEcIFIc SAFETY rULES
Minimum Gauge for cord Sets
volts
120v 25 (7.6)
Ampere rating
240v
50 (15.2)
More Not More
Than
Than
0 6
6 10
10 12
12 16
Some dust created by power sanding, sawing, grinding, drilling, and other construction
lead from lead-based paint.
crystalline silica from bricks and cement and other masonry products.
arsenic and chromium from chemically-treated lumber (CCA).
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
Use of this tool can generate and/or disburse dust, which may cause serious and per-
ALWAyS wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19)
ALWAyS USE SAFETy GLASSES. (ANSI Z87.1) and (CAN/CSA Z94.3) Everyday eye-
ANSI Z87.1 eye protection (CAN/CSA Z94.3)
ANSI S12.6 (S3.19) hearing protection
NIOSH/OSHA/MSHA respiratory protection
................ direct current
(grounded)
(double insulated)
ADDITIONAL SAFETY rULES FOr PAINT rEMOvAL
Total Length of cord in Feet (meters)
50 (15.2) 100 (30.5) 150 (45.7)
100 (30.5) 200 (61.0) 300 (91.4)
AwG
18 16 16
18 16 14
16 16 14
14 12 Not Recommended
A ................. amperes
W ................ watts
.............. alternating current
.............. alternating or direct current
n o ............... no load speed
............... earthing terminal
............... safety alert symbol
BPM ........... beats per minute
RPM ........... revolutions per minute
14
12
12