Installation Instructions
Free-Standing Electric Ranges
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT —
Save these
instructions for local inspector's use.
• IMPORTANT —
Observe all
governing codes and ordinances.
•
Note to Installer – Be sure to leave these
instructions with Consumer.
FOR YOUR SAFETY:
WARNING
Tip-Over Hazard
• A child or adult can tip the range and be killed.
• Install the anti-tip bracket to the wall or floor.
• Engage the range to the anti-tip bracket by sliding the
range back such that the foot is engaged.
• Re-engage the anti-tip bracket if the range is moved.
• Failure to do so can result in death or serious burns
to children or adults.
If you did not receive an anti-tip bracket with your
purchase, call 1.800.626.8774 to receive one at no
cost. (In Canada, call 1.800.561.3344.) For installation
instructions of the bracket,
visit: GEAppliances.com.
(In Canada, GEAppliances.ca.)
MATERIALS YOU MAY NEED
Squeeze Connector
(UL Listed 40 AMP)
(For Conduit
4-Wire Cord 4' long OR
Installations Only)
3-Wire Cord 4' long
1
REMOVE PACKAGING MATERIALS:
materials could result in damage to the appliance. Remove all packing parts from oven,
racks, heating elements and drawer. Also, remove protective film and labels on the outer
door, cooktop and control panel.
•
Note to Consumer – Keep these
instructions for future reference.
•
Skill level – Installation of this appliance
requires basic mechanical skills and
advanced electrical skills.
•
Proper installation is the responsibility of the
installer.
•
Product failure due to improper installation
is not covered under Warranty.
Anti-Tip Bracket
Kit Included
WARNING
Before beginning
the installation, switch power off at
service panel and lock the service
disconnecting means to prevent power
from being switched on accidentally.
When the service disconnecting
means cannot be locked, securely
fasten a prominent warning device,
such as a tag, to the service panel.
TOOLS YOU WILL NEED
Drill with 1/8" Bit
Tape Measure
Safety Glasses
Pliers
Adjustable Wrench
1/4" Nut Driver
Level
Tin Snips
Failure to remove packaging
2
PREPARE THE OPENING (FOR INDOOR USE ONLY)
See illustrations for all rough-in and spacing dimensions. The range may be placed with 0"
clearance (flush) at the back wall and side walls of the cabinet.
SINGLE OVEN
On models with baking
2
1 2
"
or warming drawers,
30"
electrical outlet must
not be in this area.
25"
*
7"
14
1 2
29
"
7 8
47"
4"
25
3 8
"
47
5 8
"
Acceptable electrical outlet area.
Orient electrical receptacle so the
length is parallel to floor.
NOTE: Use a 4' power cord to prevent interference with
the storage drawer. Power cords 4
' to 6' long may
1 2
have to be dressed to allow for proper drawer closing.
MINIMUM DIMENSIONS BETWEEN COOKTOP,
WALLS AND ABOVE THE COOKTOP:
A. Make sure the wall covering, countertop, flooring and
cabinets around the range can withstand the heat (up
to 200°F) generated by the range.
B. Allow 30" minimum clearance between surface units
and bottom of unprotected wood or metal cabinet, or
allow a 24" minimum when bottom of wood or metal
cabinet is protected by no less than 1/4" thick flame
retardant millboard covered with not less than No 28
MSG sheet metal, (.015"), .015" thick stainless steel,
.024" aluminum or .020" copper.
C. This appliance has been approved for 0" spacing to
adjacent surfaces above the cooktop. However, a 6"
minimum spacing to surfaces less than 15" above the cooktop and adjacent
cabinet is recommended to reduce exposure to steam, grease splatter and heat.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space
above the cooktop should be avoided. If cabinet storage space is to be provided above
the cooktop, the risk can be reduced by installing a range hood that projects at least 5" beyond
the front of the cabinets. Cabinets installed above the cooktop must be no deeper than 16".
DOUBLE OVEN
3
1 4
"
2
1 2
"
*
29
7 8
"
"
47"
7
1 2
"
36"
25
3 8
"
45"
B
NOTE C
A
30"
23
1 2
"
3
1 4
"
7
3 4
"
3"
C
Both
Sides
A