EINHELL GC-EL 3000 E Manual De Instrucciones página 8

attachments such as deflectors and/or grass
catching devices are missing.
•
When working outdoors, use only extension
cords which are approved for outdoor use.
Extension cords must have a minimum cross-
section of 1.5 mm
must be splash-proof.
Operation
•
Always trail the power cord behind the tool.
•
If the power cord or extension cord is
damaged, pull the plug out of the socket.
NEVER TOUCH THE CORD BEFORE THE
PLUG HAS BEEN PULLED OUT OF THE
SOCKET.
•
Do not carry the tool by its power cord.
•
Always pull out the power plug:
- When the tool is not being used, when it
is being transported or when you leave it
unsupervised.
- When you are checking the tool, cleaning it
or removing blockages.
- When you want to carry out cleaning or
maintenance work on the tool or replace
accessories.
- After the tool impacts with foreign bodies or
you notice unusual vibrations.
•
Use the tool only in broad daylight or in well-lit
conditions.
•
Do not underestimate the forces involved.
Make sure you stand squarely and keep your
balance at all times.
•
If possible, avoid using the tool on wet grass.
•
Ensure that you maintain a steady foothold
particularly while working on slopes.
•
Always walk. Never run.
•
Always keep the ventilation opening clean.
•
Never direct the blower/vacuum hole at
persons or animals.
•
The machine may only be used at reasonable
times of the day, i.e. not in the early morning
or late evening when it will be a nuisance to
other people. Permitted times of use specified
by local authorities must be observed.
•
The machine must be run at the lowest
possible motor speed required to carry out
the work.
•
Remove all foreign objects with a rake and
brush before starting any blowing work.
•
Where conditions are dusty, dampen the
surface a little or use a sprinkler attachment.
•
Use the full-length blower nozzle extension
so that the air current can work near to the
ground.
•
Watch out for children, pets, open windows,
Anl_GC_EL_3000_E_SPK7_USA.indb 8 Anl_GC_EL_3000_E_SPK7_USA.indb 8
. The plug connections
2
EN
etc. and blow the foreign objects safely away
from them.
Maintenance and storage
•
Check that all nuts, bolts and screws are
securely tightened in order to be sure that the
machine is in a safe working condition.
•
Frequently check the collection bag for signs
of wear and deformation.
•
Use only genuine accessories and spare
parts.
•
For your own safety, replace worn or
damaged parts without delay.
•
Electric tools should be kept in a dry place
when not in use.
•
If the power cord for this device is damaged,
it must be replaced by the manufacturer or at
a service center or similarly trained personnel
to avoid danger.
&
Servicing of Double Insulated Appliances
Your blower is double-insulated to give you
added safety. In a double insulated appliance,
two systems of insulation are provided instead
of grounding. No grounding means is provided
on a double insulated appliance, nor should a
means for grounding be added to the appliance.
Servicing a double insulated appliance requires
extreme care and knowledge of the system
and should be done only by qualifi ed service
personnel. Replacement parts for a double
insulated appliance must be identical to the
parts they replace. A double insulated appliance
is marked with the words double insulated or
"double insulation". The symbol (square within a
square) may also be marked on the appliance.
Safety Rules and Instructions:
Polarized Plug
To reduce the risk of electric shock, this
equipment has a polarized plug (one blade
is wider than the other). This equipment must
be used with a suitable polarized 2 wire or 3
wire extension cord. Polarized connections will
fi t together only one way. Make sure that the
receptacle end of the extension cord has large
and small blade slot widths. If the plug does not
fi t fully into the extension cord, reverse the plug.
If it still does not fi t, obtain a suitable extension
cord. If the extension cord does not fi t fully into
the outlet, contact a qualifi ed electrician to install
the proper outlet. Do not change the tool plug or
extension cord in any way.
- 8 -
21.03.2023 10:51:56 21.03.2023 10:51:56