DeWalt DWE6411 Manual De Instrucciones página 10

English
paint particles. Workers should wash and clean up
BEFORE eating, drinking or smoking. Articles of food,
drink, or smoking should not be left in the work area
where dust would settle on them.
2. EnViROnMEnTAl sAFETY
‑ Paint should be removed in such a manner as to
minimize the amount of dust generated.
‑ Areas where paint removal is occurring should be
sealed with plastic sheeting of 4 mils thickness.
‑ Sanding should be done in a manner to reduce
tracking of paint dust outside the work area.
3. ClEAning AnD DisPOsAl
‑ All surfaces in the work area should be vacuumed
and thoroughly cleaned daily for the duration of
the sanding project. Vacuum filter bags should be
changed frequently.
‑ Plastic drop cloths should be gathered up and
disposed of along with any dust chips or other
removal debris. They should be placed in sealed
refuse receptacles and disposed of through regular
trash pick‑up procedures. During clean up, children
and pregnant women should be kept away from the
immediate work area.
‑ All toys, washable furniture and utensils used by
children should be washed thoroughly before being
used again.
Tool Care
• Keep your machine as clean as possible by wiping with
a clean cloth and blowing through it with air after every
5 hours of use.
• Don't use harsh chemicals or solvents to clean the tool.
These chemicals could seriously damage the plastic.
• Avoid overloading your sander. Overloading will result in
a considerable reduction in speed and efficiency and the
unit will become hot. In this event, run sander at a "no
load" condition for a minute or two.
• Brush inspection and replacement should be completed
by your local dealer or authorized service center.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
8
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this product could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
Lubrication
Self lubricating bearings are used in the tool and periodic
relubrication is not required. However, it is recommended
that, once a year, you take or send the tool to a service center
for a thorough cleaning and inspection.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment (including brush inspection and replacement)
should be performed by a D
D WALT authorized service center or other qualified service
e
personnel. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
Three Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/
support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D WALT Industrial Tool Co., 701 East
e
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country‑specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
WALT recommended
e
WALT. Call 1‑800‑4‑D WALT
e e
WALT factory service center, a
e
WALT
e
WALT
e