Kyocera AJ6500V Manual Del Usuario página 5

JIG SAW SAFETY WARNINGS
1. Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
2. Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body leaves it
unstable and may lead to loss of control.
3. Use blades suitable for the material to be cut for effi-
cient and safe operation.
Make sure the saw blade is tightly secured, as de-
scribed in the operation instructions.
4. Excessive pressure and bending while cutting may
break the blade.
5. Cutting with the body of the tool fixed in a vice is very
dangerous.
6. It is extremely dangerous to point the cutting surface
towards any person.
INSTRUCTIONS FOR SAFE HANDLING
1. Make sure that the tool is only connected to the volt-
age marked on the name plate.
2. Never use the tool if its cover or any bolts are missing.
If the cover or bolts have been removed, replace them
prior to use. Maintain all parts in good working order.
3. Always secure tools when working in elevated posi-
tions.
4. Never touch the blade, drill bit, grinding wheel or other
moving parts during use.
5. Never start a tool when its rotating component is in
contact with the workpiece.
6. Never lay a tool down before its moving parts have
come to a complete stop.
7. ACCESSORIES : The use of accessories or attach-
ments other than those recommended in these in-
structions might present a hazard.
8. REPLACEMENT PARTS : When servicing use only
identical replacement parts.
DESCRIPTION
1. See through guard
2. Saw guide fence
3. Speed control button
4. Trigger
5. Lock button
6. Hex. socket head bolt 15. Guide pin
7. Roller guide
8. Hex. key wrench
9. Jig saw blade
SPECIFICATIONS
Stroke length
Cutting capacity
in wood
in steel
Input
Stroke speed
Overall length
Net weight
* Be sure to check the nameplate on the product, be-
cause the voltage is subject to change depending on
the area in which the product is to be used.
10. Selector lever
11. Anti-splinter plate
12. Hex. socket head bolt
13. Base
14. Hex. socket head bolt
16. Blade holder
17. Base cover
18. Vacuum hose
20 mm (25/32")
65 mm (2-9/16")
6 mm (1/4")
400 W
0 - 3,000 min -1
205 mm X 173 mm X 67 mm
(8-1/16" X 6-13/16" X 2-5/8")
1.7 kg (3.7 lbs.)
STANDARD ACCESSORIES
Jig saw blade, Hex. key wrench, Saw guide fence,
Anti-splinter plate
APPLICATIONS
(Use only for the purposes listed below.)
1. Cutting wood, resin boards and thin metal sheets.
BLADE INSTALLATION (Fig. 1)
BE SURE TO DISCONNECT THE PLUG FROM THE POW-
ER SOURCE BEFORE INSTALLING THE BLADE.
AJ6500V
1. Loosen the hex. socket head bolt (6) by using the hex.
key wrench (8).
2. Insert the blade completely into the groove of the
blade holder(16).
3. Tighten the hex. socket head bolt.
AJ6500VL
1. With the lever of the blade holder (16) turned, move
the back of the blade along the v-groove of the roller
guide (7), and insert it fully into the groove of the blade
holder.
2. Release the lever of the blade holder (16), and check
that there is no gap between the back of the blade and
the blade holder.
NOTE!
Check that the back of the saw blade enters the groove
of the roller guide (7).
ORBITAL ACTION (Fig. 2)
To obtain the best cutting action with various types of ma-
terial, it is necessary to adjust the orbital action of the saw
blade. This tool has a selector lever (10) on the side of the
housing.
Selections range from 0 for straight reciprocating blade
action to for largest orbit of the blade.
When cutting into wood and plastic or other soft materials,
a large swing is required, i.e. position , or .
For steel and similar hard materials, the cutting action
should not be so great, so position 0 should be used.
However, if a sharp and precise cutting surface is required
for soft materials, then position 0 may also be used.
It is also intended for thin materials, as well as for knife or
rasp work.
SWITCH (Fig. 3)
This tool is started and stopped by squeezing and releasing
the trigger (4).
For continuous operation, press the lock button (5) while the
trigger is squeezed. Depress the trigger again to release
the lock.
This tool permits speeds of 0 - 3,000 min -1 . Speed control
button (3) permits adjusting the speed while running.
Allows operation at the desired speed.
The general rules for cutting speed apply: the harder the
material (steel), the lower the speed: the softer the material
(wood), the higher the speed.
- 4 -