Publicidad
9. La Aspiradora Robot buscará
la red para conectarse.
Espere mientras eso sucede.
OPERACIÓN DEL ROBOT DESDE LA APP
3
2
4
1
5
6
8
9
7
10
12
11
INFORMACIÓN DEL DISPOSITIVO
PROGRAMAR MODOS Y CICLOS DE LIMPIEZA
Es posible programar 30 ciclos de limpieza hasta por 7 días.
21
10. Una vez conectado haga clic en el
modelo de Aspiradora Robot adquirido
para comenzar la operación
11. Operación de la Aspiradora Robot.
La conexión se ha realizado
exitosamente. La aspiradora está lista
para limpiar
MENÚ DESDE LA APP
1. Batería del Robot
2. Configuración
3. Nombre del Robot
4. Área de limpieza
5. Tiempo de limpieza
6. Mapa
7. Ajuste de modos de limpieza
8. Ciclo de limpieza en área fija
9. Ciclo de limpieza de bordes
10. Ciclo aleatorio de limpieza
11. Regreso a la estación de limpieza
12. Ciclo de limpieza automático
1. Ir a la opción de "Configuración" o "More"
2. Seleccionar la opción de "Device information" en la cual podrá elegir las
opciones para obtener más información sobre su Aspiradora Robot.
Configuración de funcionamiento programado
de la Apiradora Robot.
Cerrar función de aspirar
Cerrar función de trapear
1. Ir a la opción de "Configuración" o "More"
2. Seleccione la opción "Scheduled Cleaning" o
"Agendar limpieza".
3. Seleccionar "Add Schedules" o "Agregar Agenda"
para poder programar un nuevo ciclo de limpieza.
FLOOR MOPPING CLEANING
The Robot Vacuum is equipped with a dust and water tank that allows it to clean floors and vacuum at the same time.
Remove dirt and stains with its dust and water tank and wet mop.
1
2
1. Remove the dust and water tank from
2. Return the dust and water tank to its
the vacuum by pressing the release
original position, lift the blue rubber lid
buttons.Turn over the dust and water
and fill it with 180 ml of water.
tank and place it on a flat surface, install
the mop as shown in the picture.
TIP: When finished, empty the water tank and let it dry before storing.
WARNING:
Do not use flavoring chemicals or detergents for this function, failure to follow these steps will cause serious
mechanical damage and will invalidate the warranty.
Do not use your Robot Vacuum Cleaner to vacuum any type of liquid or more water than that spread by the Robot
Vacuum Cleaner, failure to follow these steps will cause serious mechanical damage and will invalidate the warranty
Note: Cleaning mode and operation panel instructions are available with water tank. If you are using a dry wipe cleaning, skip this step. In order for
your Robot Vacuum to mop floors, it is important to attach the mop to it as shown. Otherwise, your Robot Vacuum will not perform the function.
TIME PROGRAMMING
The Robor Vacuum Cleaner has a time and cleaning cycle programming that allows you to customize the
day and time you want to clean your home. These settings are available through the remote control
Note: Make sure the remote control is close to the Robot Vacuum Cleaner while the setup is done.
1
2
1. Press the button on the remote
2. Press the Direction buttons to select
control then the remote control display
the desired hour.
will start flashing.
CYCLE PROGRAMMING
1
2
1. Press the button shown in the
2. Press the Direction buttons to select
picture.
the desired hour for you Robot Vacuum
Cleaner to start to clean.
To cancel cycle programming, press the button shown in the image on the remote control, holding it close for
4 seconds. The Robot Vacuum Celaner will "beep" when setup is complete.
Once the scheduled time arrives, the robot will start to clean in automatic mode
3
3. Put the dust and water tank back in
the Robot Vacuum by pressing the
extraction buttons. Your Robot Vacuum
is ready to mop.
Your Robot Vacuum Cleaner is ready
to mop.
3
3. Press the Start / Pause button; the
Robot Vacuum Cleaner will "beep" when
the setting is complete.
3
3. Press the Start / Pause button; the
Robot Vacuum Cleaner will beep when
the setting is complete.
6
Publicidad
