Publicidad
Idiomas disponibles
Idiomas disponibles
4. Only use proper tools to install this product.
5. Ensure to tighten screws well but do not over
tighten them.
GB
3. Installation
Transportation
•
The appliance is heavy. Therefore move the appliance whenever possible
by pushing or pulling it, rolling on the castors.
•
When lifting is unavoidable, use the recessed handles and lift with two
people.
•
Do not move the appliance during operation.
•
Wait at least 2 hours after moving before operating the appliance to avoid
damages on the refrigerating circuit.
Placement
When choosing an installation place, consider following points:
•
Observe all safety warnings!
•
Ensure the minimum surrounding distance in every direction of 30 cm
and 100 cm to other electrical appliances.
•
Keep a surrounding distance of minimum 50 cm around the outside
exhaust wall outlet and protect it from entering objects and moisture.
•
Make sure the wall behind the appliance is an exterior wall not a divider
and the drill holes can be made in a safe way, not obstructed by hidden
objects in the wall.
•
Ensure that a suitable power outlet is within reach at the desired location
and remains accessible after installation.
•
Consider that during dehumidifying operation water is collected inside
the appliance, which must be continuously drained through a connected
drainage hose into a suitable container or a nearby drain.
•
Ensure there are no obstacles obstructing the airflow.
The appliance is intended for the following ambient temperatures:
Mode
WARNING! Any other conditions and locations as the mentioned above
may result in reduced performance of the appliance, injuries and damage to
property.
Air exhaust
1.
Screw the wall connector and exhaust connector onto either side of the
exhaust hose.
2.
Connect the exhaust connector to the air exhaust of the appliance.
3.
Use the wall adaptor as template to mark the hole pattern on the wall.
4.
Drill the holes with a suitable power tool.
5.
Free the holes from dust and mount the wall adapter using supplied
screws and plugs.
6.
Connect the wall connector to the wall adaptor.
Notes:
•
The exhaust hose can be expanded and compressed, but for optimal
performance, keep the exhaust length to a minimum.
•
Do not extend the exhaust hose.
•
Avoid over-bending.
•
Observe the decommissioning instructions in the respective section, if
the appliance is not to be used for a longer period of time.
Drainage hose
The drainage hose is used to drain water from the upper drain outlet.
1.
Slide the drainage hose as far as possible onto the outlet.
2.
Lead the other end of the drainage hose into a suitable container or a
nearby drain.
Notes:
•
Depending on the set modus the water is either drained directly or
collected in an internal tank. Drain the water respectively.
•
Always cover the drain outlets when not in use.
•
Observe the decommissioning instructions in the respective section, if
the appliance is not to be used for a longer period of time.
IM_MAC2300C_A4_161101.indb 3
Temperature
17 °C (62 °F) - 35 °C (95 °F)
17 °C (62 °F) - 35 °C (95 °F)
13 °C (55 °F) - 35 °C (95 °F)
4. Operation
Functions
Control panel
Remote control
ON/OFF
TEMP
TEMP
MODE
FAN
SLEEP
TIMER
OFF
TIMER
ON
-
LED
SHORT
-
CUT
-
Indicators
Control panel
Remote control
Auto
Cool
Dry
-
Heat
Fan
FAN
FAN
FAN
-
FAN
Auto
Timer On
Timer Off
-
-
— /
SLEEP
-
Notes:
•
Every press of a button on the control panel and every successfully
transmitted signal from the remote control is confirmed by an audible signal.
•
All function of the appliance can be controlled via the control panel or
the remote control, with exception of the display illumination LED and
SHORTCUT buttons, which are to be found exclusively on the remote control.
Remote control
Using the control panel and the remote control alternately might lead to a
misalignment of the appliance and the information displayed on the remote
control.
•
Press any button on the remote control and the appliance adopts the
current setting from the remote control.
Notes:
•
The signals of the remote control will be transmitted with a short delay
after a button is pressed. This process is indicated by the appearing
symbol
on the remote control display.
•
The operating appliance is indicated by the symbol
control display.
•
Shortly after a reset the display of the remote control shows all display
elements for a few seconds.
3
Function
switch on or into standby
increase value
decrease value
toggle through modes
toggle through fan speeds
switch sleep mode on/off
adjustment of timer on and standby time
display and indicator lights on/off
choose preset mode and temperature
switch between °C and °F units
Function
appliance in automatic mode
appliance in cooling mode
appliance in dehumidifying mode
function not provided
appliance in fan mode
fan speed set to high
fan speed set to low
fan speed set to Auto
auto-on timer set
auto-off timer set
temperature displayed in Fahrenheit (°F)
temperature displayed in Celsius (°C)
appliance in standby / on
sleep mode active
transmitting signal
on the remote
1/11/16 11:28 AM
Publicidad
