Publicidad
Idiomas disponibles
Idiomas disponibles
Switching on/off
The appliance can only be switched on or into standby. Unplug in order to
switch off.
Press the on/standby button
or ON/OFF button to switch the appliance on
or into standby.
Notes:
•
After a power break or when the appliance is switched into standby and
on again in a short time, the refrigerating compressor will resume work
after 3 minutes (delay start). This is to prevent the refrigerating circuit
from damages.
•
If the appliance is knocked over, switch into standby and unplug
immediately. Wait at least 2 hours before operating the appliance again,
to avoid damages on the refrigerating circuit.
•
Always switch the appliance into standby before unplugging.
Modes
Mode
• appliances selects the suitable mode to
automatic
achieve the set temperature
mode
• fan speed is controlled automatically
Auto
• temperature can be adjusted
• cools down the room temperature
• the refrigerating compressor runs and stops
cooling mode
in order to maintain the set temperature
• fan speed and set temperature can be
Cool
adjusted
• dehumidifies the room with the fan
dehumidifying
• fan speed and set temperature cannot be
mode
Dry
adjusted
• fan only
fan mode
• fan speed can be adjusted
Fan
• temperature cannot be adjusted
• switches the appliance on and / or into
timer mode
standby at a user-defined time
TIME
• set temperature increases by 1 °C after 30
minutes and again by 1 °C after another 30
minutes
• temperature will be kept for the next 7
sleep mode
hours and the appliance returns then to the
previously set temperature
SLEEP
• not available during fan or dehumidifying
mode
Setting the temperature
1.
Press and hold both, the increase
control panel for more than 3 seconds to toggle between °C or °F.
2.
Press the increase
/
select a temperature between 17 °C to 30 °C or 62 °F to 86 °F.
Setting the fan speed
Press the fan speed button FAN to toggle between the speed settings. The
respective indicator on the control panel and the remote control show the
current setting.
Note: There is no indicator for the auto speed setting.
Louvre adjustment
The louvres of the air outlet can be adjusted manually in any mode to fit
required needs.
Setting the timer
The timer switches the appliance on or into standby when a user-defined
time has elapsed. When switching on, the last mode and setting will be used.
The set durations will be counted down immediately after the input without
correlation to the contrary time setting.
1.
Press the timer program button TIMER at the appliance or the specific
TIMER ON/OFF button at the remote control to enter timer setting for
either the auto-on or auto-standby timer. The respective indicator for each
setting will light up.
2.
Press the
/
buttons or the specific TIMER ON/OFF button at the
remote control as often as necessary to set a time from 0.5 to 24 hours.
3.
The setting will be saved after 5 seconds without input.
Examples:
•
To have the appliance switched off after 1 hour and on again after
another 1 ½ hours, set the auto-off time to 1.0 h and the auto-on time to
2.5 h during operation.
•
To have the appliance switched on after 8 hours and off after another 8
hours, set the auto-on time to 8.0 h and the auto-off time to 16.0 h while
in standby.
IM_MAC2300C_A4_161101.indb 4
Application
and decrease
buttons of the
or decrease
/
button separately to
Notes:
•
The adjusting increments are 0.5 hours up to 10 hours, then 1 hour up to
24 hours.
•
The respective indicator will be lit, when a time is set.
•
Switching the appliance on or into standby manually will cancel the timer
setting.
•
The timer settings will be lost once the respective actions were
conducted and the time needs to be set again.
•
The timer setting will be lost in case an error occurs (see protection and
error codes).
Preprogramming a function
•
By pushing the SHORTCUT button any function and temperature can be
saved and recalled.
1.
Choose your desired function e.g. using the MODE, TEMP
/
and FAN buttons, etc.
2.
Press and hold SHORTCUT button until the display flashes one time to
save the setting.
3.
The preset setting can be recalled anytime and from any mode by simply
pushing the SHORTCUT button.
Water drainage
Water is only collected during automatic AUTO, cooling
mode
.
During dehumidifying mode
water is drained immediately through the upper
drain outlet and the drainage hose must be continuously connected. The
water is drained through the hose into a suitable container or nearby drain.
WARNING – Danger of flooding! Do not leave the appliance unattended
when draining to an external container! Empty the container frequently to
avoid spilling over and water damage.
During automatic AUTO and cooling mode
tank, which must be drained when full. In this case the appliance will emit an
audible signal, while the display on the control panel is showing the protection
code P1. The cooling process will stop until the water is drained and the
appliance restarted, while the fan remains running.
1.
Disconnect the appliance from the power supply.
2.
Place the appliance with the lower drain outlet above a suitable container
or a drain.
3.
Remove the cover of the lower drain outlet.
4.
Attach the cover of the outlet again, when all water is drained.
5.
Connect the plug to a suitable socket.
6.
The appliance is ready to be switched on.
5. Cleaning & care
Cleaning
1.
Clean the appliance every two weeks.
2.
Clean the outer surfaces of the appliance with a damp cloth soaked in
neutral detergent. Dry it with a lint-free cloth.
3.
Do not use chemical, alkaline, abrasive or other aggressive detergents as
they might be harmful to the surfaces.
4.
Clean the air filters in warm water (below 40 °C) and neutral detergent.
Let them dry thoroughly before re-attaching.
5.
Do not open the housing of the appliance and do not insert any tools into
the air vents.
6.
This appliance does not contain any parts that can be repaired or
serviced by the consumer. Contact a qualified specialist to have it
checked and repaired as necessary.
Decommissioning
1.
Drain all water from the appliance and dry it using the fan mode
half a day in a dry, warm room to prevent mould.
2.
Switch the appliance into standby.
3.
Unplug and fix the power cord with the cable tie on the back of the
appliance.
4.
Remove the exhaust hose assembly from the appliance.
5.
Cover all drain outlets.
6.
Remove the batteries from the remote control.
7.
Close the cover of the wall adaptor.
Troubleshooting
Suspected malfunctions, errors or damage are often due to causes that the
users can fix themselves. Therefore check the product using below table
before contacting a qualified specialist. In most cases the problem can be
solved quickly.
WARNING!
Only perform the steps described within this instruction
manual! All further inspection, maintenance and repair work
must be performed by an authorised service centre or a
similarly qualified specialist.
4
GB
/
or
and dehumidifying
water is collected in an internal
for
1/11/16 11:28 AM
Publicidad
