Publicidad
Idiomas disponibles
Idiomas disponibles
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
ASSEMBLY INSTRUCTIONS
Before starting your generator, you must install the following
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
components: Handles, wheel kit, and battery holder (battery
is not included).
HANDLE INSTALLATION
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
Unpack and inspect all parts to see if there are not
1
missing or defective parts.
2
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
Find the 2 handles, the bolts and the pins.
3
Attach the handle to the frame using the holes to set
the handles.
4
Insert the bolt to hold the handle to the frame.
5
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
Set the pin in the bolt hole.
6
Repeat operations 3, 4 and 5 for the next handle
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
WHEEL INSTALLATION
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
1
Before mounting the wheels, make sure they are inflated
to a pressure between 15 psi and 20 psi, not exceeding
24 psi, as this could cause damage to you.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
2
Insert the shaft to the base through the hubs of the
frame.
3
Support the generator in blocks of wood to a sufficient
height that allows the assembly of the rim and place the
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
spacing rings on both sides.
4
Insert both wheels on the axle and secure with pins.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
FRONT SUPPORT INSTALLATION
Place the generator, without tires on wooden blocks,
1
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
allowing a place to install the front support.
2
Attach the front support to the frame with screws
provided and tighten securely, as shown in the drawing.
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
6
BATTERY INSTALLATION
CAUTION
Before installing the battery, remove the key from
the Control Panel of your generator.
Set the battery holder on the frame and secure it with the
1
screw, washer and nut as shown in the drawing.
2
Place the battery on the battery holder.
Secure the battery using the brackets attach on the
3
battery holder.
Identify the red and black wires with positive and negative
4
electrodes of the battery.
Connect the red wire to the positive terminal of the
5
battery and the black wire to the negative terminal.
(See Fig.
Handle the battery carefully as it contains highly
corrosive acid and can cause burns. Never connect the
red wire to black, this can cause damage to physical
integrity and the equipment.
ENGINE CONTROLS
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Choke
Dipstick
Publicidad
