YATO YT-82765 Manual Original página 15

GB
reduce its life and may cause irreversible damage.
During storage, the battery will be gradually unloading due to leakage conductance. The process of automatic unloading depends
on the temperature of storage, since the higher the temperature, the fastest the process. In case of incorrect storage of batteries,
there is a danger of electrolyte leakage. In case of leakage, it is required protect the leakage with neutralizing agent. In case of
contact of electrolyte with the eyes, it is required to rinse the eyes abundantly, and then immediately seek medical assistance. It
is prohibited to use a tool with a damaged battery.
In case the battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the
tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third
parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport
of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Charging the battery
Attention! Before charging you should disconnect the charger from the mains by unplugging the power supply plug from the mains.
In addition, you should clean the battery and its terminals of dirt and dust with a soft, dry cloth.
The battery has a built-in charge indicator. When you press the button, LEDs will light up (II), the more LEDs will light up, the more
fully the battery pack is charged. If the button is pressed and the LEDs are off it means that the battery is discharged.
Disconnect the battery from the tool.
Push the battery in the charger socket (XIV).
Plug the charger into a mains socket.
When the red LED lights up, it means the loading process.
When charging is complete, the red LED goes off , and green LED lights up, indicating a full charge of the battery.
Unplug the charger from the mains outlet.
Remove the battery from the charging station, by pressing the battery latch button.
Attention! If, when the charger is connected to the power supply, the green LED is on, this indicates a fully charged battery. In this
case, the charger does not start charging.
GUN OPERATION
The gun is not suitable for spraying the following paints:
High-density paints.
Paints containing abrasives such as red lead.
Coarse-grained paints.
Corrosive and base paints.
All adjustments of the nozzle must be carried out with the power supply disconnected. To do this, unplug the battery from the tool
socket.
Spray adjustment
The gun nozzle allows to set the spraying plane and width of the spaying material. The spraying plane can be set by rotating the
air nozzles. The air nozzles in a vertical position allow to obtain horizontal spraying plane, and nozzles in a horizontal position
allow to obtain vertical spraying plane of the coating material (IV). The width of the jet is set by means of an independent lever
which can be set in one of the two positions (V) signed with a symbol of a narrow or wide jet of the coating material. Do not place
the adjustment elements in positions other than those described in the manual.
CAUTION! Do not press the spray gun trigger button while adjusting the air nozzles.
Adjustment of the amount of spraying of coating material (VI)
Behind the trigger / on/off switch, there is a control knob that limits the depth of the trigger pull. The deeper the trigger is pressed,
the more spray material comes out of the spray gun nozzle. Turning the knob clockwise increases the amount of coating material,
turning the knob counterclockwise decreases the amount of coating material. The trigger has a mark to facilitate the adjustment.
Switching on/off
Fill the container with the coating material according to the procedure described above.
Make sure that the voltage on the nameplate corresponds to the mains voltage.
Make sure that the gun trigger is not pressed.
Plug the battery into the tool socket.
O R I G I N A L I N S T R U C T I O N S
15