YATO YG-05250 Manual De Instrucciones página 11

GB
PRODUCT CHARACTERISTICS
Refrigerated prep table is used for storing foodstuff s in refrigerating conditions. Depending on the intended use defi ned by op-
erating temperature range, the product can be used for storing refrigerated products or for freezing them and further storage
under this condition. Possibility of cooling down the table top also allows preparing products in refrigerated conditions. Thanks to
electronically controlled process of maintaining the temperature, device operation is effi cient and does not require intervention of
maintenance crew. Correct, reliable and safe operation of the product depends on proper operation, therefore:
Before starting product operation, please read this manual and keep it.
The supplier does not assume any liability for any damages resulting from misuse of the product, failure to follow safety regula-
tions and recommendations specifi ed in this manual. Misuse of the product will also result in loss of guarantee and warranty rights
of the user.
EQUIPMENT
The product is delivered complete and does not require assembly. Therefore, before using the product, it is required to remove
all packing and protection elements for transportation. Some preparatory actions described in the further part of this manual are
also required.
GENERAL USE RECOMMENDATIONS
Product is designed for professional use and should be operated by properly qualifi ed personnel.
The product is intended only for storing refrigerated foodstuff s. It is forbidden to store other products than foodstuff s. In particular,
do not store explosive substances in the product, such as aerosol cans containing fl ammable gas or other fl ammable and explo-
sive substances. The product is also not intended for storing medical products, blood and its components.
There is a fl ammable substance in the refrigerant system, which due to the contained nature of refrigerating medium circuit does
not pose a direct threat to the user, but the following warnings must be adhered to.
WARNING! Do not block vents in product housing or in the embedded structure.
WARNING! In order to accelerate the defrosting process, do not use any mechanical means or other means than those recom-
mended by the manufacturer.
WARNING! Protect the refrigeration system from any damage.
WARNING! Do not use any other type of electrical equipment inside the food storage compartment than the one recommended
by the manufacturer.
Unattended repair, disassembly or modifi cation of refrigerant system is forbidden.
This product is not intended for use by children below 8 years of age and persons with reduced physical or mental capabilities
and person with no experience or knowledge of the equipment. Unless they are supervised or trained how to use the product in a
safe manner so that the risks involved are understood. Children should not play with the product. Unattended children should not
perform cleaning and maintenance of the equipment.
Recommendations for the product transportation and installation
NOTE! Product installation and connections can be done only by qualifi ed personnel.
The product should only be transported in operating position. If it is necessary to tilt the product during transport or installation,
do not exceed an angle of 45 degrees. Regardless of transport and assembly methods, wait at least 12 hours between placing
the product in target location and its connection to power supply. This period of time is required to stabilize operating fl uids inside
the product systems.
Failure to observe this precaution leads to product damage.
Avoid any shocks during the transport.
Product can be placed only on a hard, fl at, level and non-fl ammable surface. Substrate should withstand the weight of appliance
itself together with foodstuff s that were put inside.
Provide proper ventilation at the place of installation of the product, none vent may be covered. Provide at least 10 cm breath-
ing-space around the product and at least 30 cm over the product. This will allow proper product ventilation. Do not place any
objects upon the product.
It is forbidden to drill any hole in the product, nor any other product modifi cation not described herein.
Place of product installation should be selected as to avoid any source of heat such as furnaces, heaters or in the vicinity of
open fl ame. Place of installation of the product should be protected from direct sunlight. Otherwise, the product performance may
deteriorate and operating costs may increase.
Humidity in the place of installation should not exceed the relative humidity provided by the product climatic class. An explanation
of signifi cance of climatic classes may be found in the further part of this manual.
O R I G I N A L I N S T R U C T I O N S
11