Publicidad
Idiomas disponibles
Idiomas disponibles
Edger Specifications
• Save all instructions
Unit Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 lb. (27kg)
Cutting Depths . . . . . . . . . . . . . . . . . . . 0-2.5 in. (0-63 mm)
Blade Diameter. . . . . . . . . . . . . . . . 9 in. (228 mm), 3 point
Gasoline Type . . . . . Regular Unleaded / 88 Octane (min.)
Gasoline Capacity . . . . . . . . . . . . . . . . . . . . . 1.7 qt. (1.6L)
Oil Type (API SG-SL) 10W-30 is recommended for all ser-
vice temperatures. See page 7 for additional information.
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . 12 oz (355 ml)
Spark Plug Model . . . . . . . . . . . . . . . . . . . . . . Torch E7RTC
Parts & Features
1. Start Lever Lever on handle which allows the engine to
run. When lever is released, engine will stop.
2. Choke Control Restricts the air intake. This allows for an
enriched fuel-air mixture which helps to start the engine.
3. Muffler Location of engine exhaust.
4. Adjustable Rear Wheel Right rear wheel is adjustable to
level the edger when edging along a curb (curb-hopping).
5. Adjustable Front Wheel Front wheel is adjustable from
side to side for balance. The front wheel can also adjust
down for curb-hopping.
6. Recoil Starter Handle The engine is equipped with an
easy pull recoil starter.
7. Index Lever Permits adjusting the cutting angle to 15
degrees, 0 degrees (vertical), or -15 degrees. To change
the angle, pull the index lever and rotate the quill assembly
to the desired angle.
8. Blade Rotating cutting element.
9. Blade Guard Prevents stones and debris from being
thrown at the operator.
10. Spark Plug/Spark Plug Wire Provides spark to ignite air/
fuel mixture. The Spark Plug Wire must be disconnected and
moved away from the Spark Plug when servicing the unit.
11. Air Filter Removes debris and contaminates from in-
take air, allowing engine to run smoothly with low exhaust.
12. Depth Selector Plate, 13. Depth Control Lever,
14. Control Rod Used to control the edging depth of cut.
15. Flameout Wire Terminals Must be connected for the
Start Lever to function.
Questions? Call Toll Free at 1-800-737-2112
Spark Plug Gap . . . . . . . . . . . 0.024-0.028 in. (0.6-0.7 mm)
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . 4 Stroke OHV
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79cc
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3600 RPM
Torque Rating . . . . . . . . . . 3.5 ft-lbs torque per SAE J1940
Bore Diam. x Stroke . . . . . . . . 2.03X1.50 in. (51.6X38 mm)
Intake Valve Clearance . 0.0079-0.0098 in.(0.20-0.25 mm)
Exhaust Valve Clearance . 0.0098-0.012 in.(0.25-0.30mm)
Angle of Ignition . . . . . . . . . . . . . . . . . . . . . . . . 25 Degrees
REAR VIEW
FRONT VIEW
1
6
15
2
11
4
5
Copyright © 2011 MAT Engine Technologies, LLC
10
3
13
7
12
14
5
Figure 1
9
8
Publicidad
