Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
TOOLS REQUIRED
Claw hammer
Safety goggles
Measuring tape
Wall hardware
Installation
1
PREPARING FOR INSTALLATION
NOTE: Before installation, make
sure all parts are present. Compare
parts with the Hardware Included list.
If any part is missing or damaged, do
not attempt to install the product.
□ Determine the desired mounting location,
and mark the wall where the unit will be
installed.
NOTE: For secure installation, the
unit must be mounted to at least one
wall stud.
4
INSTALLING THE CABINET
□ For wall stud installation, insert #12 x 3 in. screws with
washers into the stud locations (not included).
□ For drywall installation, drill holes at the appropriate
locations and insert toggle bolts with washers (not included).
□ For concrete wall installation, drill 1/4 in. holes at the
appropriate locations and insert #12 wall anchors, followed
by #12 x 3 in. screws (not included).
5
INSTALLING THE VANITY TOP
IMPORTANT: Do not use plumber's putty.
NOTE: The faucet, drain, and supply lines are not included. Install these
parts to the vanity top according to the manufacturer's instructions.
□ Apply silicone caulk/sealant (not included)
to all four corners of the cabinet.
□ Place the vanity top onto the cabinet.
□ Position the top so that it has an equal
amount of overhang on each side and use a
level to ensure the vanity top surface is level.
□ Apply silicone onto the seam between the
edge of the vanity top and the wall, smooth
the bead, and allow to cure before use.
Phillips
screwdriver
Power drill
Caulk/sealant
Keyhole saw
2
CUTTING THE OPENING FOR
PLUMBING FIXTURES
NOTE: This step applies to vanity
cabinets with full back panels only.
□ Locate and mark plumbing on the back panel.
□ Drill a pilot hole through the back panel.
□ Use a keyhole saw to cut an opening for the
plumbing fixtures.
Use and Care Guide
HARDWARE INCLUDED
AA - Knob BB - Short Screw CC - Long Screw
x 4
Level
6
INSTALLING THE HARDWARE
□ Attach knobs (AA) to the door on vanity with
short screw (BB) and to the drawers on vanity
with long screws (CC).
AA
Please contact 1-888-774-8062 for further assistance.
Item # 1000 013 635
Model # PPVNJVM30
Vanity Combo
x 1
x 3
3
POSITIONING THE
CABINET
□ Move the cabinet into
place, and use wood
shims to level the
cabinet against the wall.
BB
CC
HOMEDEPOT.COM
Publicidad
Manuales relacionados para Glacier bay PPVNJVM30
Resumen de contenidos para Glacier bay PPVNJVM30
- Página 1 Item # 1000 013 635 Model # PPVNJVM30 Use and Care Guide Vanity Combo HARDWARE INCLUDED TOOLS REQUIRED Phillips Claw hammer Safety goggles screwdriver Power drill AA - Knob BB - Short Screw CC - Long Screw Measuring tape Wall hardware...
- Página 2 Installation (continued) REMOVING THE DRAWER □ Press release levers in opposite directions while pulling drawer out of the vanity. Press Press upward downward RE-INSTALLING THE DRAWER NOTE: Drawer should install smoothly; however, there may be minor resistance when the drawer is approximately half to two-thirds installed. This is normal. □...
- Página 3 Núm. de artículo 1000 013 635 Núm. de modelo PPVNJVM30 Guía de uso y cuidado Tocadores de vanidad HERRAJE INCLUIDO HERRAMIENTAS REQUERIDAS Martillo de garra Gafas de seguridad Destornillador Phillips Taladro AA - Perilla BB - Tornillo corto CC - Tornillo largo Cinta métrica...
- Página 4 Instalación (continuado) EXTRACCIÓN DEL CAJÓN □ Presiona las palancas de desbloqueo en direcciones opuestas mientras sacas el cajón del gabinete. Presiona Presiona hacia arriba hacia abajo INSTALACIÓN DEL CAJÓN NOTA: El cajón debe instalarse suavemente aunque puede existir una pequeña resistencia cuando la instalación haya llegado aproximadamente a la mitad o a los dos tercios.