Publicidad
Idiomas disponibles
Idiomas disponibles
Entering the password
1.
Access programming mode by pressing keys INC + DEC.
2.
Press the FUN key to access the function selection menu.
3.
Select function F5 by pressing keys INC and DEC and confirm by pressing the VAL key.
4.
The letter P will appear on the left side of the display. Digit a sequence of six keys within 10 seconds. Each time a key is pressed, the letter P will flash.
6.
Upon the full sequence of six keys having been completed, the function selection menu will reappear on the display.
Failure to complete sequence within 10 seconds will abort password entry. This also avoids entry of incorrect passwords in case of any doubts as to the
sequence to be entered or erroneous pressing of any key.
The password is stored in EEPROM and is requested whenever INC+DEC are pressed to access programming mode starting from the stand-by status
(displays being off). In this case:
1.
The letter P appears on the left side of the display. Digit the sequence of six keys corresponding to the password. Each time a key is pressed, the letter
P will flash.
2.
Upon the 6-key sequence being completed, programming mode is accessed. If sequence is erroneous, the displays will go off.
Upon programming mode being accessed, any resident password may be deleted or replaced with a new one.
Note: To remove a password which has been forgotten, contact system supplier.
Deleting a resident password
1.
Press INC+DEC to access programming mode: the password will be requested.
2.
Digit in the password.
3.
Press the FUN key to access the function selection menu.
4.
Select the password entry function F5 by pressing keys INC and DEC and confirm by pressing key VAL.
5.
Allow time-out (10 seconds) to elapse; password is deleted and will not be requested upon any subsequent accessing of programming mode.
Entering a set of codes
Entry of a set of codes avoids having to perform learning of all the transmitters or of all the badges in case of packages of 10, 50 or 100 pieces with
consecutive codes.
1.
Access programming mode by pressing keys INC+DEC.
2.
Press the FUN key to access the function selection menu.
3.
Select function F6 by pressing keys INC and DEC.
4.
Confirm by pressing the VAL key. Request of the first location to be programmed will now appear, default value being 0001. Only the first decimal
point to the left will appear indicating that the initial location is being selected.
5.
Select location by pressing keys INC and DEC, and confirm by pressing the VAL key.
6.
Request of final location to be programmed will now appear. The value shown is the one which has been previously selected as the initial location so
that only a value greater than this can be selected by pressing keys INC and DEC. The last decimal point to the right will now appear indicating that
the final location is being selected.
7.
After selection of the final location, confirm by pressing the VAL key. The M/2000E will now set itself up to accept transmission of a code. Once code
has been received (via radio or any of the connected readers), it is entered in the initial location. All subsequent locations up to the final one may be
entered with codes obtained by increasing the initial code by one unit.
Example: initial location = 120, final location = 127, received code = 112233
Upon all locations having been entered with the code, system will return to the function
selection menu.
Deleting a set of codes
1.
Access programming mode by pressing keys INC+DEC.
2.
Press the FUN key to access the function selection menu.
3.
Select function F7 by pressing keys INC and DEC.
4.
Confirm by pressing the VAL key. Request of the first location to be deleted (that is, the default value 0001) will now appear. Only the first decimal
point to the left will appear indicating that the initial location is being selected.
5.
Select location by pressing keys INC and DEC, and confirm by pressing the VAL key.
6.
Request of final location to be deleted will now appear. The value shown is the one which has been previously selected as the initial location so that
only a value greater than this can be selected by pressing keys INC and DEC. The last decimal point to the right will now appear indicating that the
final location is being selected.
7.
After having selected the final location, confirm by pressing the VAL key; the letter -C- will now appear on the left-hand side of the display.
8.
Press the VAL key again to confirm. The M/2000E will now automatically delete all the codes stored in the set of programmed locations.
Upon deletion being completed, system will return to the function selection menu.
Deleting all codes
Deletion of all codes avoids having to scroll all locations and having to delete one code at a time in case of memory having to be fully cleared.
1.
Access programming mode by pressing keys INC+DEC.
2.
Press the FUN key to access the function selection menu.
3.
Select function F8 by pressing keys INC and DEC.
4.
Confirm by pressing the VAL key. The letter C will appear on the left side of the display.
5.
Confirm again by pressing the VAL key. The M/2000E will fully delete the code area only. All other stored parameters (relay times, channels, etc.) will
remain unaltered.
Upon deletion being completed, system will return to the function selection menu.
PRASTEL S.r.l. Via del Vetraio, 7 40138 Bologna Italy - Tel. +39-051-6023311 Fax +39-051-538460
E-mail: info@prastel.com - Web site: http://www.prastel.com
M2000E_ 06_1999
Location
120
121
122
123
124
125
126
127
5
M/2000E
Code
⇒
112233
⇒
112234
⇒
112235
⇒
112236
⇒
112237
⇒
112238
⇒
112239
⇒
112240
M E M B E R
O F
Publicidad
