WERKU WK400290 Instrucciones Originales página 5

ENG
factors, the pilot light may not illuminate
leave the battery to cool and then restart the charging
process Disconnect the charger from the power
►
supply Hold the battery firmly and pull the charger
►
plug out Due to their internal chemical composition,
►
batteries that have never been used or left unused for
long periods of time may not produce their full output
during their first or second use
phenomenon, to restore the optimal battery activity,
repeat this process three times with each of them.
TURNING ON THE FRONT LAMP.
Caution! Do not look into the light or see the
►
source of the light directly
turn on the light The lamp keeps on lighting while
►
the switch trigger is being pulled
off 10 -15 seconds after releasing the trigger (4).
TORQUE SELECTION.
To select the torque, turn the selector to the
►
desired position (5)
►
indicated on the selector
small screws on light jobs, select low torque
grader Each click in the clockwise means to
►
increase the produced torque
torque position is the drilling position, indicated
with an icon of a drill bit on the regulator
position the clutch mechanism is not active, for
tougher screwing jobs (6).
INSTALLING/REMOVING ACCESSORIES.
After inserting the accessory in the automatic
►
bit holder, tighten the holder firmly by turning it
to the right (clockwise) as seen from the front (7)
If the accessory comes loose during use, turn
►
off the cordless impact-driver drill and tighten
the bit holder firmly
►
loosen the bit holder by turning it to the left (anti-
clockwise) as seen from the front
battery is correctly installed
the correct spin direction (8).
GEAR SELECTOR.
The cordless impact-driver drill has two gears; a
►
short one and another long one
gear move the selector to the desired position (9).
SWITCH.
When pressed, the bit will turn, and if not will
►
come to a halt The spin speed may be controlled
►
by varying pressure on the trigger
gently, the bit will turn slowly, increasing with the
pressure applied.
In this case,
►
This is a temporary
►
Pull the switch trigger to
►
The lamp turns
►
There are 18 positions
When working with
►
The maximum
►
►
To remove the accessory,
Check that the
►
Make sure you select
►
To change the
►
If pressed
►
FUNCTION SELECTOR.
The cordless impact-driver drill includes an
►
impact system
turn the switch to the picture marking "hammer"
(10) With the impact function connected, it is
►
only necessary to push with a little bit force
much force can overload the motor unnecessarily
To work again without the impact function, turn
►
the switch to the picture marking "drill" (11).
TURN SELECTOR.
The turn selector only can be activated when
►
the cordless impact-driver drill is stopped
turn selector has two different positions
rotation to the right, set the turn selector to the
left position
turn selector to the right position.
BELT CLIP.
With the belt clip the cordless impact-driver drill
►
can be hung onto a belt (12)
hands free and the cordless impact-driver drill is
always at hand.
MAINTENANCE.
The cordless impact-driver drill has been
►
designed for a long working life with minimum
In this
maintenance
care of the cordless impact-driver drill and
regular cleaning
unplug the cordless impact-driver drill from the
power source before cleaning or performing any
maintenance
may be cleaned effectively using compressed
air after each use
available, use a brush to remove dust from the
cordless impact-driver drill
vents and switch levers must be dept clean and
free of foreign matter
by inserting pointed objects through openings
Cetain cleaning agents and solvents damage
►
plastic parts, among them are gasoline, carbon
tetrachloride, chlorinated cleaning solvents,
ammonia and household cleaners containing
ammonia
cordless impact-driver drill.
ENVIRONMENT PROTECTION.
The materials and components that have
►
been used to manufacture this product can be
re-used and recycled
an Integrated Management System that is in
charge of the correct elimination of the residues
of this product
5
English
To work with the impact function
►
For a rotation to the left, set the
►
The user has both
►
Optimum use depends on correct
►
To prevent accidents, always
►
The cordless impact-driver drill
►
If compressed air is not
►
Motor ventilation
►
Do not attempt to clean
►
Do not use any of these to clean the
►
Werku
► ®
Do not eliminate this product
►
Too
►
The
►
For a
►
is adhered to