Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
TOOLS REQUIRED
Hammer
Safety goggles
Measuring tape
Wall hardware
Installation
1
PREPARING FOR INSTALLATION
NOTE: Before installation, make sure all parts
are present. Compare parts with the Hardware
Included list. If any part is missing or damaged,
do not attempt to install the product.
□ Determine the desired mounting location,
and mark the wall where the unit will be
installed.
NOTE: For secure installation, the unit
must be mounted to at least one wall stud.
3
INSTALLING THE CABINET
□ For wall stud installation, insert #12 x 3 in. screws
with washers into the stud locations (not included).
□ For drywall installation, drill holes at the appropriate
locations and insert toggle bolts with washers (not included).
□ For concrete wall installation, drill 1/4 in. holes at the
appropriate locations and insert #12 wall anchors,
followed by #12 x 3 in. screws (not included).
4
INSTALLING THE VANITY TOP
IMPORTANT: Do not use plumber's putty.
NOTE: The faucet, drain, and supply lines are not included. Install these
parts to the vanity top according to the manufacturer's instructions.
□ Apply silicone caulk/sealant (not included) to all four corners of the cabinet.
□ Place the vanity top onto the cabinet.
□ Position the top so that it has an equal amount of overhang on each side
and use a level to ensure the vanity top surface is level.
□ Apply silicone onto the seam between the edge of the vanity top and the
wall, smooth the bead, and allow to cure before use.
NOTE: Matching side and back splashes available, sold separately.
To purchase, visit your local Home Depot store or go to homedepot.com.
5
INSTALLING THE HARDWARE
□ Attach the handle (AA) to the cabinet with the provided screw (BB).
Phillips screwdriver
Power drill
Caulk/sealant
Use and Care Guide
HARDWARE INCLUDED
AA - Handle x 1
Level
2
POSITIONING THE CABINET
□ Move the cabinet into place, and use wood
shims to level the cabinet against the wall.
Please contact 1-888-774-8062 for further assistance.
Item #1003 431 352
Item #1003 431 348
Model # PPSPADVR18
Model # PPSPAWHT18
Vanity Combo
BB - Handle Screw x 2
BB
AA
HOMEDEPOT.COM
Publicidad
Manuales relacionados para Glacier bay PPSPADVR18
Resumen de contenidos para Glacier bay PPSPADVR18
- Página 1 Item #1003 431 352 Item #1003 431 348 Model # PPSPADVR18 Model # PPSPAWHT18 Use and Care Guide Vanity Combo TOOLS REQUIRED HARDWARE INCLUDED Hammer Safety goggles Phillips screwdriver Power drill AA - Handle x 1 BB - Handle Screw x 2...
- Página 2 Troubleshooting Problem Possible Cause Solution The doors do not align or The hinges are misaligned. Hold the door while loosening Up — Down the space is too big or too screws. Align the doors properly, In — Out tight between the doors. and re-tighten the screws.
- Página 3 Núm. de artículo 1003 431 352 Núm. de artículo 1003 431 348 Núm. de modelo PPSPADVR18 Núm. de modelo PPSPAWHT18 Guía de uso y cuidado Combo de tocador HERRAMIENTAS REQUERIDAS HERRAJE INCLUIDO Martillo Gafas de seguridad Destornillador Phillips Taladro AA - Manija x 1 BB - Tornillo de manija x 2 Cinta métrica...
- Página 4 Resolución de fallas Problema Posible causa Solución Arriba — Abajo Las puertas no se alinean Las bisagras están Sostenga la puerta mientras o el espacio es demasiado desalineadas. afloja los tornillos. Alinee las grande o está demasiado puertas adecuadamente y Izquierda —...