Thanks For Choosing Toto; Before Installation; Common Tools Needed; Included Parts - Toto DuoFit WT171M Manual De Instrucciones

TABLE OF CONTENTS

Thanks for Choosing TOTO!

Common Tools Needed

Included Parts

Before Installation

Installation Procedure
Servicing Procedures
Warranty
THANKS FOR CHOOSING TOTO!
The mission of TOTO is to provide the world with healthy, hygienic and more
comfortable lifestyles. We design every product with the balance of form and function
as a guiding principle. Congratulations on your choice.
COMMON TOOLS NEEDED
• Hacksaw
• Flat File
• Drill
• 1/8" (3mm) Drill Bit
INCLUDED PARTS
Check to make sure you have all these parts from the package:
In Wall Tank
(Carrier)
Parts in Bag 1
Outlet Pipe Upper bracket Lag Screw
(8)
Threaded Lower Anchor
Mounting Stud (2) Bracket (2)
• 3-1/2" (89mm) Hole Saw
• 7/16" (11mm) Open or Boxed-end Wrench
• Tape Measure
• Carpenter's Level
Parts in Bag
Outlet Pipe Inlet Pipe
Mud Guard Mud Guard
Push Plate
Rough In
Parts in Bag 2
Lubricated
Flange Pipe Inlet Pipe sponge
Nut Cap Washer Stud bolt Flange
(2) (2) (2) (2)
2
2 ■
Read these instructions thoroughly before beginning work.
2
■
Please leave these instructions with the customer. They contain important mainte-
2
nance and warranty information.
3
■
If necessary, remove the existing toilet.
4-7
■
8-9
CAUTION! Be sure to properly bleed all air from the piping system prior to using
10
any TOTO products. Trapped/compressed air can cause damage to the fl ushing
system and toilet bowl.
Prepare the support for the carrier as shown. Consult with a building contractor and/or
local codes for any additional requirements. Add a double wall studs (king and jack)
and double header per the shown dimensions. Confirm that the opening is square.
inch
( mm )
46- "
7
16
( 1180 )
39- "
3
8
( 1000 )
½"
( 13 )
NPT
Water
Supply
½" NPT
Optional
washlet
Connection
Header
(Double)
Optional
GFCL
Electrical
Outlet
12"
BEFORE INSTALLATION
22- "
13 ( 580 )
16
½"
( 13 )
NPT
Water
Supply
7- " 1
16
( 180 )
D
"
7 ( 22 )
8
1- "
3 ( 35 )
8
3- "
15
16
( 100 )
12- "
5
8
( 320 )
Finished Floor
" - "
5 5
8 16
( 15-135 )
6- " 6- "
7 ( 175 ) 3 ( 157 )
8 16
inch
8- "
5 ( 218 )
8
Toilet Rim
Height (R)
King Studs
15"
16"
17"
18"
19"
mm
Toilet Rim
Height (R)
381
2"
( 51 )
406
22- "
7
( 580 )
8
432
Trimmer
(Jack)Studs 457
45- " - 50- "
3 3
8 8
( 1150-1280 )
483
Table 1: Dimensions measured from
Sole Plate
Finished Floor
Sub-Floor
(plywood or concrete)
3
H
3- "
1 ( 89 )
2
R
3- " 3
( 86 )
8
System Threaded Mounting
Height (H) Stud Height (D)
31" 11-29/64"
32" 12-7/16"
33" 13-15/32"
34" 14-29/64"
35" 15-1/2"
System Threaded Mounting
Height (H) Stud Height (D)
787 291
813 316
835 342
864 367
889 393
Finished Floor