Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

SUMMER WAVES
SKIMMERPLUS
READ AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
For answers to common questions, setup videos and troubleshooting tips, please visit
support.polygroupstore.com or call Customer Service: (888) 919-0070
DO NOT RETURN PRODUCT TO STORE
Should you encounter a problem with your Polygroup
must be made directly to Polygroup
or review the FAQ and instructional videos at support.polygroupstore.com. If you are still unable to correct the problem, please contact Polygroup
Customer Service at (888) 919-0070. Please have the product type, model number and your purchase receipt ready, so that our Customer Service
Representative can assist you in resolving the problem. You may be asked to return all or part of the product for inspection and/or repair. Do not
return any product to Polygroup
Polygroup
Trading Limited, (hereinafter "Polygroup
®
workmanship for 180 days from the date of purchase. Original Purchaser must retain proof of such purchase in the form of an original store sales receipt and must
produce such upon request by Polygroup
applies only to the original purchaser of the product and is limited solely to the repair or replacement of the product, to be decided in Polygroup
Consequential damages, including claims for loss of water, pool chemicals, damage, or labor are not covered under this Limited Warranty. This Warranty will be
declared invalid should the Purchaser modify or repair the product themselves or by unauthorized persons; use non-Polygroup
use the product in contravention of the manufacturer's Instructions; use improper voltage; abuse the product in any way; or through accident or negligence. Normal
wear-and-tear is not covered under this Warranty, nor are acts of God outside the control of Polygroup
grow through the ground cloth and/or pool liner, as this is not a manufacturing defect.
IN NO EVENT SHALL Polygroup
PARTY FOR DIRECT OR CONSEQUENTIAL DAMAGES. Some states or countries, or other jurisdictions, do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
FOR ABOVE GROUND SWIMMING POOLS
SFX330 Model
Product, please DO NOT return the product to the place of purchase. All Warranty claims
®
. Prior to contacting Customer Service, please first review the Troubleshooting Guide in the Installation Manual,
®
without a Return Merchandise Authorization number.
®
LIMITED WARRANTY
") warrants to the original purchaser only, the SFX type Electric Filter Pump against defects in material and
®
or its designated agents. Warranty claims cannot be processed without a valid proof of purchase. This Limited Warranty
®
, THEIR AUTHORIZED AGENTS, RELATED ENTITIES, OR EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER
®
DISTRIBUTED BY: Polygroup
Unit 606, 6th Floor, Fairmont House, No.8 Cotton Tree Drive, Central, Hong Kong
OWNER'S MANUAL
FILTER PUMP
®
please visit www.polygroupstore.com
. Polygroup
will not be held responsible for grasses that may
®
®
Trading Limited
®
®
To order parts and accessories,
's sole discretion.
®
parts or accessories with the product;
®
Manual #
09C3A4USA016
®

Publicidad

loading

Resumen de contenidos para Polygroup SUMMER WAVES SKIMMERPLUS SFX330

  • Página 1 Warranty claims cannot be processed without a valid proof of purchase. This Limited Warranty ® applies only to the original purchaser of the product and is limited solely to the repair or replacement of the product, to be decided in Polygroup ’s sole discretion.
  • Página 2 TABLE OF CONTENTS Warnings 3 ~ 6 Preliminary Steps, Important Notes & Pump Power Info Parts List 7 ~ 8 Setup Instructions & Use of Pump 9 ~ 10 Pump Motor Care & Maintenance Filter Cartridge Use & Care Pool Water Care Pump Disassembly &...
  • Página 3 CUSTOMERS THAT PURCHASE POOLS MAY BE REQUIRED BY LOCAL OR STATE LAW TO INCUR ADDITIONAL EXPENSES WHEN INSTALLING A POOL, IN ORDER TO COMPLY WITH STATE OR LOCAL LAWS REGARDING FENCING AND OTHER SAFETY REQUIREMENTS. CUSTOMERS SHOULD CONTACT THEIR LOCAL BUILDING CODE ENFORCEMENT OFFICE FOR FURTHER DETAILS. POLYGROUP IS NOT RESPONSIBLE FOR ANY ADDITIONAL EXPENSES THAT YOU MAY INCUR.
  • Página 4 Turn on the pump for the recommended hours daily. If you are unsure of the time frames please refer to support.polygroupstore.com for the recommended Pump Operation Hours based on pool types and sizes. Clean and replace filter cartridge frequently. Replace only with genuine Polygroup / Summer Waves Brand filter cartridge.
  • Página 5 OWNER’S MANUAL First Aid 1. Keep a working phone and a list of emergency numbers near the pool. 2. Become certified in cardiopulmonary resuscitation (CPR). In the event of an emergency, immediate use of CPR can make a lifesaving difference. Special Warning 1.
  • Página 6 ASME American Society of Mechanical Engineers Two Park Avenue, New York NY 10016-5990 Contact: 800-843-2763 (U.S. & Canada) 973-882-1170 (outside North America) www.asme.org NSPI National Spa and Pool Institute (see APSP) UL Underwriters Laboratories 333 Pfingsten Road,Northbrook IL 60062-2096 Contact: 877-854-3577 or 847-272-8800 www.ul.com NSF NSF International P.O.
  • Página 7 ) or its latest approved edition. ® ® 3. This Filter Pump is manufactured by Polygroup and ETL control number 4000608 and 4006317 – double insulated and grounded – 120VAC 60Hz. All units must ® have a minimum of 105VAC to start and run properly.
  • Página 8 Outside Pool Wall Inside Pool Wall Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday. Extended operating days and hours during peak season requirements.
  • Página 9 OWNER’S MANUAL SETUP INSTRUCTIONS Before assembly, take a few minutes to identify and become familiar with all the parts. WARNING: CLIMBING HAZARD! PLEASE PREVENT CHILDREN FROM CLIMBING ON THE FILTER CANISTER TO GAIN ACCESS TO THE POOL. Skimmer Installation 1. Set up your pool following the pool Owner’s Manual instructions. Do NOT fill 2.
  • Página 10 Pump Installation 7. From inside the Skimmer Canister , snap the pins of the Weir into 8. Slide close the Top Cover onto the Skimmer Canister the pivot slots, one after another. The Weir should now stand upright but not stuck. Push-in Inside Pool Wall Weir installation...
  • Página 11 Contact and consult your local pool supplies store for solutions/treatment, and maintain an adequate pH level of pool water (see POOL WATER CARE, p. 12). 5. Dispose of any used filter media in accordance with applicable regulations/legislation. 6. Always use genuine Polygroup Summer Waves Filter Cartridges; they are available at where you ®...
  • Página 12 POOL WATER CARE 1. The following items are required to get your pool ready for use. They are available at polygroupstore.com or your local pool supplies stores: a. Test Kit – for checking the chlorine and pH levels of the pool water. Use it daily and adjust with the required chemicals. b.
  • Página 13 OWNER’S MANUAL PUMP SERVICING INSTRUCTIONS The most efficient way to troubleshoot or replace the Pump is to disassemble the entire filtration system. Please drain the water level to below the pool’s Skimmer Opening, then disassemble the system following the steps below. CAUTION: 1.
  • Página 14 You may need to reach inside the Canister to free the Pump Motor. 5. Slowly take out the Motor Assembly . Be careful not to lose the Rubber Nozzle or Canister Gasket STEP 2: Rotor Inspection/Replacement The Pump is consisted of a Rotor Assembly and its related parts.
  • Página 15 OWNER’S MANUAL STEP 3: Pump Replacement/Reassembly 1. Lubricate the Canister Gasket . Turn the Skimmer Canister upside IMPORTANT: make sure that the cord of the down, place the Gasket into the inner groove at the bottom. Motor Assembly is placed through the Motor Seal Nut BEFORE replacing the Pump.
  • Página 16 3. Once the Motor is correctly aligned, match the threads of the Motor Seal to that of the Canister, and tighten by twisting the Nut counterclockwise. IMPORTANT: make sure the Nut and Canister are not cross-threaded; otherwise leaks may occur. Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
  • Página 17 OWNER’S MANUAL TROUBLESHOOTING GUIDE Problem Cause Solution A Plug the GFCI Power Cord Set to a grounded power outlet. Then press the RESET A Pump not plugged in button to start the Pump. 1. Motor doesn’t start, B GFCI Power Cord Set B Reset your circuit breaker on the electrical panel.
  • Página 18 OWNER’S MANUAL REPLACEMENT PARTS ORDERING INFORMATION Description Part # P58PP4511W05 Motor Seal Nut Rubber Nozzle P58P4179AK01 Pump Motor Assembly P58X0330C000 Canister Gasket / Motor Seal P58105001K01 Top Cover P58PP4509W05 P58SFX000W01 Weir Foam Filter Cartridge P581031035PR Weir P58PP1956W05 Skimmer Canister P58PP4510W05 P58030001K01 Hose Connection O-Ring Hose Clamp...
  • Página 19 Las reclama ciones de garantía no pueden procesarse sin un justificante de compra ® válido. Esta garantía limitada solo se aplica al comprador original del producto y se limita a la reparación o sustitución del producto, a discreción de Polygroup . Los ®...
  • Página 20 ÍNDICE Advertencia 3 ~ 6 Pasos Preliminares, Notas Importantes Acerca De La Bomba De Filtración, Potencia De La Bomba Lista De Piezas 7 ~ 8 Instrucciones De Montaje, Uso De La Bomba 9 ~ 10 Cuidado Del Motor De La Bomba, Mantenimiento De La Piscina Uso Y Cuidado Del Cartucho De Filtro Cuidado Del Agua De La Piscina Desmontaje Y Almacenamiento De La Bomba...
  • Página 21 ADICIONALES AL INSTALAR UNA PISCINA, EN CUMPLIMIENTO DE LAS LEYES ESTATALES O LOCALES RELATIVAS AL VALLADO Y OTROS REQUISITOS DE SEGURIDAD. LOS CLIENTES DEBEN PONERSE EN CONTACTO CON LAS AUTORIDADES LOCALES CORRESPONDIENTES PARA MÁS INFORMACIÓN. POLYGROUP NO ES RESPONSABLE POR GASTOS ADDICIONALES QUE PUEDAN OCCURIR.
  • Página 22 Limpie y cambie el cartucho de la bomba del filtro con frecuencia. Reemplazar solo con un cartucho de filtro original de la marca Polygroup...
  • Página 23 MANUAL DEL USUARIO filtro de la bomba debe colocarse de manera que no pueda ser usado por los niños pequeños como medio de acceso a la piscina. No deje juguetes dentro de la piscina al terminar de usarla, ya que los juguetes y objetos similares podrían atraer a los niños a la piscina. 3.
  • Página 24 APSP Association of Pool & Spa Professionals (formerly National Spa and Pool Institute) 2111 Eisenhower Avenue, Suite 500 Alexandria VA 22314-4679 Contacto: 703-838-0083 www.apsp.org ASME American Society of Mechanical Engineers Two Park Avenue, New York NY 10016-5990 Contacto: 800-843-2763 (U.S. & Canada) 973-882-1170 (outside North America) www.asme.org NSPI National Spa and Pool Institute (see APSP) UL Underwriters Laboratories...
  • Página 25 ® ® edición más reciente aprobada. 3. Los sistemas de bomba de filtración de la serie SFX son fabricados por Polygroup con el número de control de ETL 4000608 y 4006317, con doble aislamiento y ® conexión a tierra, 120 VCA y 60 Hz. (Todas las unidades deben contar con 105 VCA como mínimo para empezar a funcionar correctamente).
  • Página 26 Parte Fuera de La Piscina Parte Interior de La Piscina Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST) Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
  • Página 27 MANUAL DEL USUARIO INSTRUCCIONES DE MONTAJE Antes de montar el producto, dedique unos minutos a comprobar el contenido y familiarícese con todas las piezas. ADVERTENCIA: COLOQUE ESTE PRODUCTO APARTADO DE LA PISCINA A FIN DE EVITAR QUE LOS NIÑOS SE SUBAN A ÉL Y ACCEDAN A LA PISCINA. Instalación del skimmer (rebosador) 1.
  • Página 28 Instalación de la bomba 7. Desde dentro de la caja del skimmer , enganche los pines de la Compuerta 8. Deslice y cierre la Cubierta superior sobre la Caja en las ranuras de los pivotes, uno después de otro. La Compuerta ahora debe del skimmer estar de pie, pero no atascada.
  • Página 29 (ver CUIDADO DEL AGUA DE LA PISCINA, p. 12). 5. Elimine cualquier filtro usado en conformidad con las regulaciones/leyes correspondientes. 6. Siempre use Cartuchos de filtro Polygroup Summer Waves ; se encuentran disponibles donde ha ®...
  • Página 30 CUIDADO DEL AGUA DE LA PISCINA 1. Se requieren los siguientes artículos para que su piscina esté lista para usarse. Se encuentran disponibles en polygroupstore.com o en sus tiendas locales de suministros de piscina: a. Kit de prueba - para verificar los niveles de cloro y de pH del agua de la piscina. Úselo diariamente y ajuste con las sustancias químicas requeridas. b.
  • Página 31 MANUAL DEL USUARIO INSTRUCCIONES DE MANTENIMIENTO DE LA BOMBA La manera más eficiente de resolver las problemas o de reemplazar la Bomba es desmontando todo el sistema de filtración. Drene el nivel de agua por debajo de la abertura del skimmer, luego desmonte el sistema siguiendo los pasos a continuación. PRECAUCIÓN: 1.
  • Página 32 Podría tener que alcanzar dentro de la caja para liberar el motor de la bomba. 5. Saque lentamente el ensamblaje del motor . Tenga cuidado de no perder la Boquilla de goma o el Empaque de la caja PASO 2: Inspección/Reemplazo del rotor La Bomba consiste de un Ensamblaje del rotor y sus partes relacionadas.
  • Página 33 MANUAL DEL USUARIO PASO 3: Reemplazo/Reensamblaje de la Bomba 1. Lubrique el Empaque de la caja . Voltee de cabeza la Caja del IMPORTANTE: asegúrese que el cable del skimmer , coloque el empaque en la ranura interna en la parte inferior. Conjunto del motor esté...
  • Página 34 3. Una vez que el motor esté correctamente alineado, aparee las roscas de la Tuerca del sello del motor a las de la Caja y luego ajuste la Tuerca hacia la izquierda. IMPORTANTE: asegúrese que la Tuerca y la Caja no tengan las roscas cruzadas;...
  • Página 35 MANUAL DEL USUARIO GUÍA DE RESOLUCIÓN DE PROBLEMAS Problema Causa Solución A Enchufe el set de cable de alimentación GFCI a un tomacorriente correctamente puesto a A La Bomba no está enchufada tierra. Luego presione el botón RESET para iniciar la Bomba. 1.
  • Página 36 MANUAL DEL USUARIO INFORMACIÓN SOBRE EL PEDIDO DE PIEZAS DE REPUESTO Descripción N.º De Pieza Llave Tuerca de sellado del motor P58PP4511W05 Boquilla P58P4179AK01 P58X0330C000 Conjunto del motor Junta del cartucho P58105001K01 Cubierta superior P58PP4509W05 Espuma de retención P58SFX000W01 Cartucho de filtro tipo P581031035PR Rebosadero P58PP1956W05...