Descargar Imprimir esta página

stayer HL105 Manual De Instrucciones página 19

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 1
Open water tap
Press the safety lock 1 to release the trigger 2. Fully
press the trigger 2 until there is a constant flow of water to
clear the air from the machine and water supply hose.
Release trigger 2. Press the trigger safety lock 1.
Press button
on main switch 5.
Point the power gun 3 downwards. Press the trigger
safety lock to release the trigger 2. Fully press the trigger
2.
Stopping
Release trigger 2. Press the trigger safety lock. The
power gun is now locked and can not be operated
accidentally. Press button
Close water tap. Unplug the machine from the electric
supply.
Press the trigger safety lock 1 to release the trigger 2.
Fully press the trigger 2 until there is no more water
pressure in the machine. Release trigger 2. Press the
trigger safety lock 1.
Disconnect water supply hose from machine and water
supply.
Fine-tuning operations
Vario-jet-fan power lance
Twist the front ring to adjust from a pencil to a fan jet and
vice versa.
4.2 Instructions for use
.
General
Ensure that the machine is on level ground.
Do not overreach with the high pressure hose or move
the pressure washer by pulling the hose, this could cause
the machine to become unstable and fall over.
Do not kink or drive a motor vehicle over the high
pressure hose. Do not expose the high pressure hose to
sharp edges or corners. Never use the roto nozzle to
clean motor vehicles.
Operating with Detergents
Only use approved detergents. Unsuitable
detergents may damage the unit and the object
being cleaned.
Fill the detergent tank 10 with detergent, dilute as
recommended.
To spray detergent move vario-jet-fan power lance to low
pressure mode.
We recommend that you use detergent sparingly for the
sake of the environment. Observe the recommended
dilution on the detergent label.
on the main switch 5.
ENGLISH
14
Recommended cleaning method
Step 1: Loosening dirt
Spray on detergent sparingly and allow to react for a short
time.
Step 2: Removing dirt
Spray off the loosened dirt with the high-pressure spray.
Note! When cleaning a vertical surface spray off
dirt/detergent from the bottom and work in an
upwards direction. Rinse from the top and work
downwards.
5. Maintenance instructions
5.1. Cleaning, maintaining, lubricating,
sharpening
Warning! Switch off, remove plug from mains before
adjusting, cleaning or if cable is cut, damaged or
entangled.
Cleaning/inspecting the strainer
Expose the strainer 13 in the machine water inlet
connection by removing the inlet connector 7.
Rinse and replace. If damaged replace.
Never use the pressure washer without the strainer or a
damaged strainer.
Maintenance
!
Stop, remove plug from the power supply
and disconnect from water supply.
Note! To ensure long and reliable service, carry
out the following maintenance regularly.
Regularly check for obvious defects such as loose
fixings, and worn or damaged components.
Check that covers and guards are undamaged and
correctly fitted. Carry out necessary maintenance or
repairs before using.
If the pressure washer should happen to fail despite
the care taken in manufacture and testing, repair
should be carried out by an authorised service agent
for STAYER garden products.
Environmental Protection
Chemicals dangerous to the environment must not be
allowed to enter the ground, ground water or ponds,
streams, etc.
For the use of cleaning agents, observe the instructions on
the package and the prescribed concentration exactly.
For the cleaning of motor vehicles the local regulations
should be observed: Do not allow oil sprayed off to enter
into the ground water. Recycle raw materials instead of
waste disposal.
14

Publicidad

loading

Este manual también es adecuado para:

Hl110Hl160Hl190Hl220