Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

READ ME FIRST:
Thank you for purchasing a Front Runner Slimline II Rack.
This Roof Rack consists of a kit that contains:
1.) A Slimline II Tray
2.) A mounting system specific to your vehicle
This document will help you fit the Slimeline II Tray to your specific vehicle.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR
VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY
INJURY OR DEATH TO YOU OR TO OTHERS. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER
PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE
PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE
INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO
NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT
THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A
PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
REV_A01
Jeep GRAND CHEROKEE WKII
SLIMLINE II RACK
1255MM X 1560mm
(
IMPORTANT WARNING!
1
)
FAJG001 / KRJG004T
INSTALL TIME: 1 Hour

Publicidad

loading

Resumen de contenidos para Front Runner FAJG001

  • Página 1 VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO OTHERS. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE.
  • Página 2 GET ORGANIZED... Here is what you are looking at: Please note that only the right hand side's components and fitment has been shown. Item # Quantity Description M8 x 20 HEX BOLT You will need: FOOT RAIL - 1 LEFT, 1 RIGHT 10 mm Flat or Socket Wrench M8 FLAT WASHER 13 mm Flat or Socket Wrench...
  • Página 3 Fit the foot rails Looking on the inside of the vehicle's original rook tracks loosen and remove the six bolts securing each track to the vehicle. Remove the tracks from the vehicle. Place a Foam Washer (Item 10), white backing facing up, over each of the bosses on the vehicle's roof. ( C ) Place the Foot Rails onto the vehicle's roof, lining up the mounting holes in the bottom of the Foot Rails with the bosses on the vehicles roof.
  • Página 4 FIT THE RACK Note: If your Slimline II Tray is not already assembled, assemble it as per the Slimline II Tray Universal Assembly Instruction (Document RRSTUNI). Read Step 3A before fitting the Wind Deflector Before fitting the Wind Deflector, and with the Rack in the upside down position, (Check with product sticker.
  • Página 5 You'll find a small amount of settling has happened. Go on many more adventures, periodically checking all nuts, bolts, screws and fittings. Front Runner can not recommend a maximum load carrying capacity. Please refer to your vehicle manufacturer's recommendations.
  • Página 6 FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL. NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
  • Página 7 M8 x45 Button Head Bolt Thick Joiner Piece Thin Joiner Piece Side Profile Corner Combined Slat 28 X M8 x 25 Button Head Bolt 12 X Standard Slat M6 x 10 Button Head Bolt FIGURE 1.1 RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 8 Slide the matching Side Profile over the two Joiner pieces, remembering to insert a Nyloc Nut, and fasten once again using a M8 x 45 Button Head Bolt. Repeat the above steps for the other side. RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 9 Combined Slat and Standard Slats, aligning the holes and loosely inserting the M8 x 25 Button Heads as you work your way to the Combined Slat at the other end. RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 10 Push the Corner into position as shown, aligning the hole in the Corner with the Rivnut already inserted in the Combined Slat. Use a M6 x 12 Button Head Bolt (Item 10) and fasten the Corner in position. RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 11 RACK ASSEMBLY - WIND DEFLECTOR IN THE BOX TOOLS NEEDED Slimline II Tray M8 Half Nut Wind Deflector (1LH + 1RH) Schnorr Washer M8 x 12 Button Head Bolt FIGURE 1.2 RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 12 Slide them to the center of the Combined Slat making sure that the Schnorr Washer is above the T-slot Channel. Assemble Items 2, 4 & 5 to both LH & RH Wind Deflectors (Item 3) as shown. RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 13 Wind Deflectors slightly apart, leaving a gap of about 20 - 30mm. USEFULL TIP - PRE-LOAD TIE DOWN RINGS It is usefull to fit Tie-Down Rings (RRAC012) to your Front Runner Rack for future use before you fit any accessories. Insert the Tie Down Rings into the machined slots and position them in the center of the rack.
  • Página 14 It's easy! Take care of your Front Runner gear the same way you do the exterior of your vehicle: Rinse with clean water and wipe down with a soft dry cloth. For stubborn spots, use a soft brush and mild soap.
  • Página 15 BEFESTIGUNGEN VOR EINER VERWENDUNG REGELMÄßIG AUF EINSTELLUNG, ABNUTZUNG ODER SCHÄDEN ZU PRÜFEN. LIES DAHER UNBEDINGT VOR DER MONTAGE ODER DER VERWENDUNG ALLE MIT DEINEM FRONT RUNNER PRODUKT GELIEFERTEN ANWEISUNGEN UND HINWEISE. FALLS DU NICHT ALLE ANWEISUNGEN ODER HINWEISE VERSTEHST ODER DU KEINE TECHNISCHE ERFAHRUNG BESITZT UND MIT DEM ZUSAMENBAUEN NICHT VERTRAUT BIST, SOLLTEST DU DAS PRODUKT VON TECHNISCHEM FACHPERSONAL ODER EINER ANDERWEITIG QUALIFIZIERTEN PERSON VERBAUEN LASSEN.
  • Página 16 32 X M8 Selbstsichernde Mutter M8 x 45 Rundkopfschraube Dickes Verbindungsstück 4 MM 5 MM Dünnes Verbindungsstück Seitenprofil Eckstück Kombileiste 28 X M8 x 25 Rundkopfschraube 12 X Querleiste M6 x 10 Rundkopfschraube ABBILDUNG 1.1 RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 17 Schiebe das zugehörige Seitenprofil über die zwei Verbindungsstücke und denk daran, eine selbstsichernde Mutter einzusetzen. Befestige auch diese Verbindung mit einer m8 x 45 Rundkopfschraube. Wiederhole die oben beschriebenen Schritte für die andere Seite. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 18 5 MM Kombileiste sein. Verwende eine M8 x 25 Rundkopfschraube (Teil 8) und ziehe sie mit einem 5 mm-Innensechskantschlüssel fest. Die Plattform bleibt mit der Unterseite nach oben gedreht, für die Montage der 7 Querleisten. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 19 Schau Dir nochmal Schritt 3.1 an - Schiebe danach die zweite Kombileiste in die zwei Seitenprofile und befestige sie, wie in Schritt 3.2 beschrieben. FESTZIEHEN ALLER SCHRAUBEN Ziehe mit Deinem 5 mm-Innensechskantschlüssel alle Rundkopfschrauben fest. Das empfohlene Drehmoment für die M8 Rundkopfschrauben ist 20 Nm oder 15 ftlb. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 20 Vergewissere Dich in der jeweiligen Montageanleitung, ob das der Fall ist. MONTAGE DES WINDABWEISERS INHALT DU BENÖTIGST Slimline II Dachträger M8 Halbmutter Windabweiser (1L + 1R) 5 MM Unterlegscheibe M8 x 12 Rundkopfschraube ABBILDUNG 1.2 RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 21 (Teil 2, 4 & 5) wie dargestellt in die Kombileiste. Schiebe sie bis zur Mitte der Kombileiste, wobei Du sicherstellen musst, dass die Unterlegscheibe über der T-Nut sitzt. Montiere Teil 2, 4 & 5 wie abgebildet an beiden Windabweisern. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 22 (RRAC012) am Dachträger vor der Montage von zusätzlicher Ausrüstung bereits vorhanden sind. Einfach die Ringschrauben in die T-Nut auf den Leisten in der Mitte befestigen und somit vorbereitet sein, falls weitere Accessoires und Ausrüstung montiert werden soll. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 23 Im salzigen Küstenklima oder verschneiten Regionen, in denen Streusalz auf den Straßen genutzt wird, verwende auf Silikonbasis beschaffenes Öl oder Spray, um die Muttern und Schrauben dauerhaft vor Korrosion zu schützen. HOL DIR NOCH MEHR AUSRÜSTUNG VON FRONT RUNNER Besuche uns Online auf www.FrontRunnerOutfitters.com Markiere uns immer und überall! #FrontRunnerOutfitters #BornToRoam...
  • Página 24 LOS PRODUCTOS PARA SU AJUSTE, DESGASTE Y DAÑOS. POR LO TANTO, DEBE LEER Y COMPRENDER TODAS LAS INSTRUCCIONES Y PRECAUCIONES SUMINISTRADAS CON SU PRODUCTO FRONT RUNNER ANTES DE LA INSTALACIÓN O EL USO. SI USTED NO ENTIENDE TODAS LAS INSTRUCCIONES Y PRECAUCIONES, O SI NO TIENE EXPERIENCIA MECÁNICA Y NO ESTÁ...
  • Página 25 Pieza de ensamble gruesa Pieza de ensamble delgada Perfil lateral Esquina Barra combinada 28 X M8 x 25 Tornillo cabeza de botón 12 X Barra estándar M6 x 10 Tornillo cabeza de botón FIGURA 1.1 RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 26 Deslice el perfil lateral coincidente sobre las dos piezas de ensamble, recordando insertar una tuerca nyloc, y apriete una vez más usando un tornillo cabeza de botón M8 x 45. Repite los pasos anteriores para el otro lado. RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 27 El orificio final del perfil lateral debe alinearse con el orificio en la barra combinada. Utilice un cabeza de botón M8 x 25 (artículo 8) y apriete ligeramente con una llave Allen de 5mm. RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 28 Con su llave Allen de 5mm, apriete todos los tornillos cabeza de botón. El ajuste de par recomendado para los tornillos cabeza de botón M8 es de 20 Nm o 15 ft lb. © 2019 FRONT RUNNER VEHICLE OUTFITTERS RRSTUNI_REV_A04...
  • Página 29 Schnorr está por encima del canal ranura en T. Ensamble los elementos 2, 4 y 5 a ambos deflectores de viento LH & RH (artículo 3) como se muestra. RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 30 MONTAJE DE BACA - DEFLECTOR DE VIENTO EN LA CAJA HERRAMIENTAS NECESARIAS Baca portaequipaje Slimline II M8 Tornillo medio Deflector de viento (1LH + 1RH) Arandela de seguridad Schnorr M8 x 12 Tornillo cabeza de botón FIGURA 1.2 RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 31 CONSEJO ÚTIL - ANILLOS DE AMARRE DE PRECARGA Es de mucha utilidad el colocar los anillos de amarre (RRAC012) en la baca portaequipajes de Front Runner para su uso futuro antes de colocar cualquier accesorio. Inserte los anillos de amarre por medio de las ranuras y colóquelos en el centro de...
  • Página 32 ¡Es fácil! Cuida tu equipo Front Runner de la misma manera que haces con el exterior de tu vehículo: Enjuague con agua limpia y limpie con un paño suave y seco. Para manchas persistentes, usa un cepillo suave y un jabón suave.

Este manual también es adecuado para:

Krjg004t