Publicidad
Idiomas disponibles
Idiomas disponibles
Operating Instructions
General Safety
Information
(Continued)
● Read and understand
tool labels and manual.
Failure to follow warn-
ings, dangers, and cau-
tions could result in
DEATH or SERIOUS INJURY.
● Do not use any type
of reactive gases,
including, but not lim-
ited to, oxygen and
combustible gases, as
a power source. Use
filtered, lubricated, regulated com-
pressed air only. Use of a reactive
gas instead of compressed air may
cause the nailer to explode which
will cause death or serious personal
injury.
● Use only a pressure-
regulated compressed
air source to limit the
air pressure supplied
to the tool. The regu-
lated pressure must
not exceed 110 psi. If the regulator
fails, the pressure delivered to the
tool must not exceed 200 psi. The
nailer could explode which will
cause death or serious personal
injury.
● Never use gasoline
or other flammable
liquids to clean the
nailer. Never use the
nailer in the presence
of flammable liquids or gases.
Vapors could ignite by a spark and
Nailer Components And Specifications
• REQUIRES: 0.7 SCFM with 10 nails
per minute @ 90 psi
• AIR INLET: 1/4" NPT
• NAIL SIZE RANGE: 1" to 2-1/2"
• MAGAZINE CAPACITY:
100 Nails per load, 16 gauge
• WEIGHT: 4 lbs., 15 oz.
• LENGTH: 12-1/2"
• HEIGHT: 11-7/8"
• MAXIMUM PRESSURE: 110 psi
• PRESSURE RANGE: 70 - 110 psi
www.chpower.com
cause an explosion which will result
in death or serious personal injury.
● Always remain in a
firmly balanced posi-
tion when using or
handling the nailer.
● Do not remove,
tamper with, or
otherwise cause
the Work Contact
Element (WCE) or
O
trigger to become
CO
2
inoperable. Do not operate any tool
which has been modified in a like
fashion. Death or serious personal
injury could result.
● Do not touch the
trigger unless dri-
ving nails. Never
attach air line to
nailer or carry
nailer while
touching the trigger. The tool could
eject a fastener which will result in
death or serious personal injury.
a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
● Always discon-
nect the tool
from the power
source when
unattended,
performing any
maintenance or repair, clearing a
jam, or moving the tool to a new
Quick Clear
Latch
No-Mar Tip
● Always fit tool
CAMPBELL
CAMPBELL
HAUSFELD
HAUSFELD
PROFESSIONAL
PROFESSIONAL
● Never place hands or
Warning
● Never carry the
indicates
Adjustable Exhaust
Trigger
Work Contact
Element (WCE)
2
Model JB006750
location. Always reconnect the air
line BEFORE loading any fasteners.
Do not load the tool with fasteners
when either the trigger is depressed
or the Work Contact Element (WCE)
is engaged. The nailer could eject a
fastener causing death or serious
personal injury.
with a fitting
or hose cou-
pling on or
near the tool in
such a manner
that all compressed air in the tool is
discharged at the time the fitting or
hose coupling is disconnected. Do
not use a check valve or any other fit-
ting which allows air to remain in the
nailer. Death or serious personal
injury could occur.
any other body parts in
the nail discharge area
of the nailer. The nailer
might eject a fastener
and could result in
death or serious personal injury.
nailer by the air
hose or pull the
hose to move the
nailer or a com-
pressor. Keep
hoses away from
heat, oil and sharp edges. Replace
any hose that is damaged, weak or
worn. Personal injury or tool dam-
age could occur.
Depth
Name, Spec
Adjustment
and Warning
Wheel
Label (back-side
and top)
Magazine
Magazine
(open)
Latch
Publicidad
