Publicidad
Idiomas disponibles
Idiomas disponibles
6.
The motor is to be switched off immediately in
case that the equipment shows any problem or
abnormal sign.
7.
Switch off and remove the battery cartridge
when resting and when leaving the equipment
unattended, and place it in a safe location to
prevent danger to others or damage to the
equipment.
8.
Avoid using the machine in bad weather
conditions especially when there is a risk of
lightning.
Personal protective equipment
Wear eye protection and stout shoes at all
1.
times while operating the machine.
2.
Always wear substantial footwear and long
trousers while operating the machine.
Starting up the equipment
1.
Make sure that there are no children or other
people nearby, also pay attention to any ani-
mals in the working vicinity. Otherwise stop
using the equipment.
2.
Before use always check that the equipment
is safe for operation. Check the security of the
cutting tool and the guard and the switch trig-
ger/lever for easy and proper action. Check for
clean and dry handles and test the function of
the start/stop.
3.
Check damaged parts before further use of
the equipment. A guard or other part that is
damaged should be carefully checked to deter-
mine that it will operate properly and perform
its intended function. Check for alignment of
moving parts, binding of moving parts, break-
age of parts, mounting, and any other condi-
tion that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced by our authorized ser-
vice center unless indicated elsewhere in this
manual.
4.
Switch on the motor only when the hands and
feet are away from the cutting tool.
5.
Before starting make sure that the cutting tool
has no contact with any objects.
Method of operation
1.
Only use the equipment in good light and
visibility. During the winter season beware
of slippery or wet areas, ice and snow (risk
of slipping). Always ensure a safe footing on
slopes and be sure to walk and never run.
2.
Take care against injury to feet and hands from
the cutting tool.
3.
Never stand on a ladder and run the
equipment.
4.
Never climb up into trees to perform cutting
operation with the equipment.
Never work on unstable surfaces.
5.
6.
Remove sand, stones, nails etc. found within
the working range. Foreign particles may dam-
age the cutting tool and can cause dangerous
kick-backs.
7.
Should the cutting tool hit stones or other hard
objects, immediately switch off the motor and
inspect the cutting tool.
8.
Inspect the cutting tool at short regular inter-
vals for damage (detection of hairline cracks
by means of tapping-noise test).
9.
Before commencing cutting, the cutting tool
must have reached full working speed.
10. The cutting tool has to be equipped with the
appropriate guard. Never run the equipment
with damaged guards or without guards in
place!
11.
All protective installations and guards sup-
plied with the equipment must be used during
operation.
12. Always remove the battery cartridge from the
equipment:
whenever leaving the equipment
—
unattended;
before clearing a blockage;
—
—
before checking, cleaning or working on
the equipment;
—
after striking a foreign object;
whenever the equipment starts vibrating
—
abnormally.
13. Always ensure that the ventilation openings
are kept clear of debris.
14. Cutting means continues to run after the motor
is switched off.
15. If the blades stop moving due to the stuck of
foreign objects between the blades during
operation, switch off the tool and remove the
battery cartridge, and then remove the foreign
objects using tools such as pliers. Removing
the foreign objects by hand may cause an injury
for the reason that the blades may move in reac-
tion to removing the foreign objects.
Cutting Tools
Employ only the correct cutting tool for the job
in hand.
Maintenance instructions
1.
The condition of the equipment, in particular of
the cutting tool of the protective devices must
be checked before commencing work.
2.
Turn off the motor and remove the battery
cartridge before carrying out maintenance,
replacing cutting tools or cleaning the equip-
ment or cutting tool.
3.
When not in use, store the equipment indoors
in dry and high or locked-up place - out of the
reach of children. Clean and maintain before
storage.
SAVE THESE INSTRUCTIONS.
WARNING:
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
11 ENGLISH
DO NOT let comfort or familiarity
Publicidad
