Publicidad
Idiomas disponibles
Idiomas disponibles
Using the Control Switch
Due to a lockout mechanism, the control switch
can only be adjusted when the trigger is not pulled.
Always allow the motor to come to a complete stop
before using the control switch.
Forward
1. For forward (clockwise) rotation, push the control
switch to the left side of the tool. Check the direc-
tion of rotation before use.
2. For reverse (counterclockwise) rotation, push the
control switch to the right side of the tool. Check
direction of rotation before use.
Starting, Stopping and Controlling Speed
1. To start the tool, grasp the handle firmly and pull
the trigger.
2. To vary the speed, increase or decrease the pres-
sure on the trigger. The further the trigger is pulled,
the greater the speed.
3. To stop the tool, release the trigger. Make sure
the tool comes to a complete stop before laying
the tool down.
Operating
Position the tool, grasp the handles firmly and pull
the trigger. Always hold the tool securely using both
handles to maintain control. This tool has been de-
signed to achieve top performance with only moder-
ate pressure. Let the tool do the work.
If the speed begins to drop off when drilling large or
deep holes, pull the bit partially out of the hole while
the tool is running to help clear dust. Do not use water
to settle the dust since it will clog the bit flutes and
tend to make the bit bind in the hole. If the bit should
bind, a built-in, non-adjustable slip clutch prevents
the bit from turning. If this occurs, stop the tool, free
the bit and begin again.
APPLICATIONS
To reduce the risk of electric shock,
WARNING
check work area for hidden pipes
and wires before drilling.
Drilling in Wood, Composition Materials
and Plastic
When drilling in wood, composition materials and
plastic, select the drill operating mode. Start the drill
slowly, gradually increasing speed as you drill. Select
low speeds for plastics with a low melting point.
Drilling in Metal
When drilling in metal, select the drill operating mode.
Use high speed steel twist drills or hole saws. Use a
center punch to start the hole. Lubricate drill bits with
cutting oil when drilling in iron or steel. Use a coolant
when drilling in nonferrous metals such as copper,
brass or aluminum. Back the material to prevent
binding and distortion on breakthrough.
Drilling in Masonry
When drilling in masonry, select the rotary hammer
operating mode. Use high speed carbide-tipped
bits. Drilling soft masonry materials such as cinder
block requires little pressure. Hard materials like
concrete require more pressure. A smooth, even
flow of dust indicates the proper drilling rate. Do not
let the bit spin in the hole without cutting. Do not use
water to settle dust or to cool bit. Do not attempt to
drill through steel reinforcing rods. Both actions will
damage the carbide.
Reverse
WARNING
any maintenance. Never disassemble the tool.
Contact a MILWAUKEE service facility for ALL
repairs.
Keep your tool in good repair by adopting a regular
maintenance program. Inspect your tool for issues
such as undue noise, misalignment or binding of
moving parts, breakage of parts, or any other condi-
tion that may affect the tool operation. Return the tool
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool to a MILWAUKEE service facility for inspection.
WARNING
never immerse your tool in liquid or allow a liquid
to flow inside it.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool to the nearest service
center.
WARNING
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
1-800-SAWDUST
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
5
MAINTENANCE
To reduce the risk of injury, always
unplug the tool before performing
Maintaining Tools
To reduce the risk of personal in-
jury, electric shock and damage,
Cleaning
Repairs
ACCESSORIES
Use only recommended accesso-
ries. Others may be hazardous.
SERVICE - UNITED STATES
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
(1.800.729.3878)
Publicidad
