Publicidad
Idiomas disponibles
Idiomas disponibles
Important notes
• Set the required operating
mode before commissioning the
FPM 611-...
• If you adjust the rotary switch for
setting the operating mode, ALL
taught-in fingerprints are deleted.
• Individual administrator, master
and user fingerprints cannot be
deleted. Administrator and master
fingerprints can only be removed via
delete mode. User fingerprints can
also be deleted during operation as
a group or ALL together.
• In some cases, it can happen that
a fingerprint cannot be scanned due
to absence of biometric characteris-
tics. In this case, try using a different
finger. This applies primarily to
children and older people. In these
cases, it is also possible that a finger-
print will not be recognised.
3 Operating mode
• Open the flap on the back of the
module with the aid of a screw-
driver.
• Set the desired operating mode
(0 to 9) on the rotary switch. Once
the required operating mode has
been set, close the flap and re-fit the
module.
4 Possible operating modes:
1
Master mode
5
Group administrator
mode
9
Administrator mode
0, 2-4, 6-8 Delete mode
Master mode
(Switch position 1)
• 1 Master fingerprint
• 100 User fingerprint
Group administrator mode
(Switch position 5)
• 1 Group administrator fingerprint
• 5 Group master fingerprint
• 100 User fingerprints distributed as
desired across all groups (maximum
of 100 user fingerprints in total).
Administrator mode
(Switch position 9)
• 1 Administrator fingerprint
• 5 Master fingerprint
• 100 User fingerprint
Delete mode
(Switch position 0, 2-4, 6-8)
• Delete all fingerprints
Which types of fingerprints exist
and what can they do?
Each fingerprint can only be scanned
for one type.
User fingerprint
• Maximum number 100
• Authorised to actuate the function
(e.g. door release). Only user fin-
gerprints can initiate this switching
function.
Master fingerprint
• Authorised to scan a maximum of
100 user fingerprints.
Administrator fingerprint
• Maximum number 1
• Authorised to scan a maximum of
5 master fingerprints.
Group administrator fingerprint
• Maximum number 1
• Authorised to scan a maximum of
5 group master fingerprints.
Group master fingerprint
• Maximum number 5
• Authorised to scan/delete a
maximum of 100 user fingerprints,
distributed across up to 5 groups.
Important notes
To ensure that you have a record
later on of the different entitle-
ments, we advise noting down the
fingerprints and the people they
belong to in the attached fingerprint
table. Before filling in, make a copy
of the fingerprint table.
5 Draw the finger correctly over
the sensor
• To ensure that the module is able
to reliably recognize your fingerprint,
draw it over the sensor to allow it
to be scanned in. Ensure that you
maintain as constant a speed, posi-
tion and light contact pressure as
possible.
• The read-in process must be
started within 10 seconds fol-
lowing activation, as otherwise the
FPM 611-... returns to the operating
status.
• Interruptions of more than 15 sec-
onds automatically return the system
to the operating mode. (Time out)
Read in fingerprints
General process for reading in a
fingerprint.
Swipe finger across
the sensor.
Right LED (green) flashes for approx.
3 second
Then the left LED (red) lights up.
Swipe finger across
the sensor again.
Right LED (green) flashes for approx.
3 second
Then the left LED (red) lights up.
Swipe finger across
the sensor again.
Right LED (green) flashes for approx.
3 seconds
Then the right LED (green) lights up.
If an adequate image cannot be
obtained, the left LED (red) flashes
rapidly three times. If this happens,
repeat the process.
9
Publicidad
