Leviton PLVSW-1LW Instrucciones De Instalación

WARNINGS AND CAUTIONS:
• WARNING: TO AVOID DEATH OR SERIOUS PERSONAL INJURY
never push objects of any kind into this product through openings, as
they may touch dangerous voltages.
• WARNING: TO AVOID DEATH OR SERIOUS PERSONAL INJURY
never touch uninsulated wires or terminals unless the wiring has been
disconnected at the network interface.
• Read and understand all instructions. Follow all warnings and
instructions marked on the product.
NOTES:
• The cable should not pass near any source of electrical noise or interference such as fluorescent circuits or motor wiring.
• Close proximity to any AC wiring should be avoided.
• All analog low voltage wiring shall be in its own conduit.
• Terminal wire range is #16-22 AWG stranded or solid.
DESCRIPTION
The PLVSW entry station is a Decora
a low voltage control device sensor. The PLVSW provides a unique control station with multiple
function operational and programming capabilities in a 1-, 2-, and 4- button configuration. The
device comes in white with a matching wallplate.
PLVSW-4LW
Basic 4-Button Function Description:
ON – all Zones to Daylight Harvesting
BRIGHT ( ) – raise all Zone light levels with a press or multiple presses
DIM ( ) – lower all Zone light levels with press or multiple presses
OFF – all Zones OFF
ELECTRICAL REQUIREMENTS
Input Voltage: 7-8 VDC
Input Current: 30mA
ENVIRONMENTAL
Operating Temperature Range: 0°C to 55°C
Relative Humidity:
INSTALLATION
NOTE: As this is an analog system, entry stations are wired directly to the designated terminal on the low voltage control device sensor.
1. Terminate the wiring to the appropriate terminals on the low voltage switch as is required for your application. The terminal block may be removed to ease
the wiring function.
Pull the block straight out of the back of the Entry Station.
2. When all wires have been terminated, gently stuff the wires back into the wall box or through the low voltage mounting ring.
3. Securely mount the station to the wall box using the provided screws. Mount the wallplate to the Entry Station.
PROGRAMMING / OPERATION
All System Programming, individual switch configuration, and other device configuration options are set at the low voltage control device sensor.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention
of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship
under normal and proper use for five years from the purchase date. Leviton's only obligation is to correct such defects by repair or replacement, at its option. For details visit www.
leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is
installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance
with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty
is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is
not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or
delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
© 2015 Leviton Mfg. Co., Inc.
AVERTISSEMENTS ET MISES EN GARDE :
• AVERTISSEMENT : AFIN D'ÉVITER LA MORT OU DE GRAVES BLESSURES, ne
jamais insérer quelque objet que ce soit dans les ouvertures de ce dispositif; il pourrait
entrer en contact avec des tensions dangereuses.
• AVERTISSEMENT : AFIN D'ÉVITER LA MORT OU DE GRAVES BLESSURES, ne
jamais toucher des bornes de raccordement ni du fil non isolés, à moins que le circuit
ne soit pas relié à l'interface réseau.
• Lire les présentes directives et s'assurer de bien les comprendre; observer tous les
avertissements et directives apparaissant sur le dispositif.
Low Voltage Entry Station
Cat. Nos. PLVSW-1LW, PLVSW-2LW & PLVSW-4LW
INSTALLATION INSTRUCTIONS
® device for controlling dimmable luminaires connected to
< 90% non-condensing
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
For Technical Assistance Call: 1-800-824-3005 - www.leviton.com
Poste de commande à basse tension
N de cat. PLVSW-1LW, PLVSW-2LW et PLVSW-4LW
os
WARNINGS AND CAUTIONS:
• DO NOT use this product near water - e.g., near a tub, wash basin, kitchen
sink or laundry tub, in a wet basement, or near a swimming pool.
• Never install communications wiring or components during a lightning storm.
• Never install communications components in wet locations unless the
components are designed specifically for use in wet locations.
• Use caution when installing or modifying communications wiring or
components.
• SAVE THESE INSTRUCTIONS.
Terminal Blocks
Common
DIRECTIVES
AVERTISSEMENTS ET MISES EN GARDE :
• NE PAS installer ce dispositif à proximité d'une source d'eau – comme une
baignoire, un bac à laver, une cuve à lessive ou un évier de cuisine –, dans un sous-
sol humide ni près d'une piscine.
• Ne jamais effectuer l'installation de câblage ou de composants de communication
pendant un orage.
• Ne jamais installer de composants de communication dans des endroits mouillés à
moins qu'il s'agisse de dispositifs conçus spécialement pour cet usage.
• On doit prendre toutes les précautions requises lorsqu'on installe ou modifie du
câblage ou des composants de télécommunication.
• CONSERVER LES PRÉSENTES DIRECTIVES.
Switch
DI-000-PLVSW-20A
ENGLISH
FRANÇAIS