Makita RT0700CX3J Manual De Instrucciones página 15

For another application, remove the base protector from
the tilt base by loosening and removing four screws.
(Fig. 24)
And then mount the base protector on the trimmer base.
Offset base (optional accessory)
(1) Offset base (optional accessory) is convenient for
work in a tight area such as a corner. (Fig. 25 & 26)
Before installing the tool on the offset base, remove the
collet nut and collet cone by loosening the collet nut.
(Fig. 27)
Install the pulley on the tool by pressing the shaft lock
and firmly tightening the pulley with a wrench. (Fig. 28)
Place the collet cone and screw the collet nut on the off-
set base as shown in the figure. (Fig. 29)
Mount the tool on the offset base. (Fig. 30)
Put an end of the belt over the pulley using a screwdriver
and make sure that its entire belt width fits over the pulley
completely. (Fig. 31)
Secure it with a locking lever on the offset base. (Fig. 32)
To install the bit, fall the tool with the offset base on its
side. Insert the hex wrench into the hole in the offset
base.
With the hex wrench held in that position, insert the bit
into the collet cone on the shaft of the offset base from
the opposite side and tighten the collet nut firmly with a
wrench.
To remove the bit at replacement, follow the installation
procedure in reverse.
(2) Offset base (optional accessory) can also be used
with a trimmer base and a grip attachment (optional
accessory) for more stability. (Fig. 33)
Loosen the screws and remove the upper section from
the offset base. Put aside the upper section of the offset
base. (Fig. 34)
Mount the trimmer base with four screws and the grip
attachment (optional accessory) with two screws on the
offset base plate.
Screw a bar type grip (optional accessory) onto the grip
attachment. (Fig. 35)
In another way of use, the knob type grip which is
removed from a plunge base (optional accessory) can be
installed on the grip attachment. To install the knob type
grip, place it on the grip attachment and secure it with a
screw. (Fig. 36)
When using as a router only with a plunge base
(optional accessory)
CAUTION:
• When using as a router, hold the tool firmly with both
hands.
To use the tool as a router, install the tool on a plunge
base (optional accessory) by pressing it down fully.
(Fig. 37)
Either knob type grip or bar type grip (optional acces-
sory) can be used according to your work. (Fig. 38)
To use the bar type grip (optional accessory), loosen the
screw and remove the knob type grip. (Fig. 39)
And then screw the bar type grip on the base.
Adjusting the depth of cut when using the plunge
base (optional accessory)
Place the tool on a flat surface. Loosen the lock lever and
lower the tool body until the bit just touches the flat sur-
face. Tighten the lock lever to lock the tool body. (Fig. 40)
Turn the stopper pole setting nut counterclockwise.
Lower the stopper pole until it makes contact with the
adjusting bolt. Align the depth pointer with the "0" gradu-
ation. The depth of cut is indicated on the scale by the
depth pointer.
While pressing the fast-feed button, raise the stopper
pole until the desired depth of cut is obtained. Minute
depth adjustments can be obtained by turning the adjust-
ing knob (1 mm per turn).
By turning the stopper pole setting nut clockwise, you
can fasten the stopper pole firmly.
Now, your predetermined depth of cut can be obtained by
loosening the lock lever and then lowering the tool body
until the stopper pole makes contact with the adjusting
hex bolt of the stopper block.
Always firmly hold the tool by both grip during operation.
Set the tool base on the workpiece to be cut without the
bit making any contact. Then turn the tool on and wait
until the bit attains full speed. Lower the tool body and
move the tool forward over the workpiece surface, keep-
ing the tool base flush and advancing smoothly until the
cutting is complete.
When doing edge cutting, the workpiece surface should
be on the left side of the bit in the feed direction. (Fig. 41)
NOTE:
• Moving the tool forward too fast may cause a poor
quality of cut, or damage to the bit or motor. Moving the
tool forward too slowly may burn and mar the cut. The
proper feed rate will depend on the bit size, the kind of
workpiece and depth of cut. Before beginning the cut
on the actual workpiece, it is advisable to make a sam-
ple cut on a piece of scrap lumber. This will show
exactly how the cut will look as well as enable you to
check dimensions.
• When using the straight guide, be sure to install it on
the right side in the feed direction. This will help to keep
it flush with the side of the workpiece. (Fig. 42)
Straight guide when using as a router (needed to
use with guide holder (optional accessory))
The straight guide is effectively used for straight cuts
when chamfering or grooving. (Fig. 43)
Install the straight guide on the guide holder (optional
accessory) with the wing nut.
Insert the guide holder into the holes in the plunge base
and tighten the wing bolts. To adjust the distance
between the bit and the straight guide, loosen the wing
nut. At the desired distance, tighten the wing nut to
secure the straight guide in place.
Straight guide (optional accessory)
The straight guide is effectively used for straight cuts
when chamfering or grooving. (Fig. 44 & 45)
To install the straight guide, insert the guide bars into the
holes in the plunge base. Adjust the distance between
the bit and the straight guide. At the desired distance,
tighten the wing bolts to secure the straight guide in
place.
When cutting, move the tool with the straight guide flush
with the side of the workpiece. (Fig. 46)
15