Sony SRS-XB22 Manual De Instrucciones

Personal Audio System
Sistema de audio personal
SRS-XB22
©2019 Sony Corporation
Printed in China
https://www.sony.net/
English Personal Audio System
Before operating the unit, please read this guide thoroughly and retain it for future reference.
CAUTION
To reduce the risk of fire, do not cover the ventilation opening of the appliance with newspapers,
tablecloths, curtains, etc. Do not expose the appliance to naked flame sources (for example, lighted
candles).
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or batteries installed) to excessive heat such as sunshine,
fire or the like for a long time.
Do not expose the batteries to extreme low temperature conditions that may result in overheating
and thermal runaway. Do not dismantle, open or shred secondary cells or batteries. In the event of
a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been
made, wash the affected area with copious amounts of water and seek medical advice. Secondary
batteries need to be charged before use. Always refer to the equipment manual for proper charging
instructions. After extended periods of storage, it may be necessary to charge and discharge the
cells or batteries several times to obtain maximum performance. Dispose of properly.
Caution on charging
When the USB plug is inserted in a wet condition, a short circuit
occurs due to the liquid (tap water, salt water, refreshing drink etc.)
attached to the main unit and charging cable or foreign matter, it
may cause abnormal heat generation or malfunction.
Never insert USB plug when the main unit or charging
cable is wet condition.
Precautions
On safety
ˎ If your skin touches this product for a long time when the power is on, it may cause a low ˎ
temperature injury.
ˎ Important information such as the model name is located inside of the cap on the rear side of the
ˎ
unit.
About the Party Booster function
If the unit hits a person or thing, it may cause an accident, injury or
malfunction. When using the Party Booster function, notice the
following.
ˎ Be sure to disconnect the micro-USB cable, etc. from the unit. ˎ
ˎ Be sure to close the cap when using the unit.
ˎ
ˎ When using the function, hold firmly and do not shake the unit
ˎ
violently so that you do not throw or drop the unit from your hand.
ˎ Before using the function, make sure that you have secured sufficient ˎ
space around the unit.
ˎ Do not hit the unit with a tool. ˎ
ˎ Do not use the function while you are driving or walking. ˎ
ˎ Keep 20 cm (7 7/8 in) or more away from the face and eyes while in ˎ
use.
ˎ Avoid using the function for a long time. Take breaks regularly. ˎ
ˎ When using the function, if you get tired, feel uncomfortable or ˎ
experience pain somewhere in your body, stop using the function
immediately.
On placement
ˎ Do not set the unit in an inclined position. ˎ
ˎ Do not leave the unit in a place subject to high temperatures, such as direct sunlight, near a heat ˎ
source or under lighting equipment.
ˎ Do not leave any objects susceptible to magnetism (cash cards, credit cards with magnetic ˎ
coding, etc.) near the unit.
ˎ Do not use or leave the unit in a car. ˎ
Others
ˎ Do not use or leave the unit in an extremely cold or hot environment (temperature outside the
ˎ
range of 5 °C – 35 °C (41 °F – 95 °F)). If the unit is used or left in outside the above range, the unit
may automatically stop to protect internal circuitry.
ˎ At high temperature, the charging may stop or the volume may reduce to protect the battery. ˎ
ˎ Even if you do not intend to use the unit for a long time, charge the battery to its full capacity ˎ
once every 6 months to maintain its performance.
About the Voice Guidance
IMPORTANT: THE SOUND GUIDANCE IS AVAILABLE IN THIS PRODUCT ONLY IN ENGLISH
Depending on the status of the unit, the voice guidance outputs from the unit as followings.
ˎ When setting the unit to the pairing mode; "Bluetooth pairing"
ˎ
ˎ When pressing the BATT (battery) button to check the battery power during the unit is turned on; ˎ
"Battery fully charged/Battery about 70%/Battery about 50%/Battery about 20%/Please charge"
ˎ When the battery power is low; "Please charge" ˎ
ˎ When the settings are completed for the Speaker Add function; "Double mode" ˎ
ˎ When pressing and holding the ADD (Speaker Add) button during the Speaker Add function; ˎ
"Left/Right/Double mode"
On Copyrights
ˎ Android, Google Play and other related marks and logos are trademarks of Google LLC. ˎ
ˎ LDAC™ and LDAC logo are trademarks of Sony Corporation. ˎ
ˎ The BLUETOOTH® word mark and logos are registered trademarks owned by the Bluetooth SIG, ˎ
Inc. and any use of such marks by Sony Corporation is under license.
ˎ The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in ˎ
other countries.
ˎ Apple, the Apple logo, iPhone, iPod and iPod touch are trademarks of Apple Inc., registered in the ˎ
U.S. and other countries.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
ˎ Use of the Made for Apple badge means that an accessory has been designed to connect
ˎ
specifically to the Apple product(s) identified in the badge, and has been certified by the
developer to meet Apple performance standards. Apple is not responsible for the operation of
this device or its compliance with safety and regulatory standards.
ˎ Other trademarks and trade names are those of their respective owners. ˎ
ˎ ™ and ® marks are omitted in the documents. ˎ
4-747-865-71(1)
Notes on waterproof and dust proof features
(Read before using the unit)
Waterproof and dust proof performance of the unit
The unit, with the cap fastened securely, has a waterproof specification of IPX7*
Reference Guide
"Degree of protection against water immersion" of the IEC60529 "Ingress Protection Rating (IP
Code)"* 3 , and a dust proof specification of IP6X*
foreign objects"* 3 .
Guía de referencia
Liquids that the waterproof performance specifications apply to
Applicable
Not applicable
* 1 IPX7 (Degree of protection against water immersion): For details, refer to the Help Guide.
* 2 IP6X (Degrees of protection against dust): For details, refer to the Help Guide.
* 3 The supplied accessories and the connectors of this unit (USB/AUDIO IN) are neither waterproof
nor dust proof.
The waterproof and dust proof performance of the unit is based on our measurements under the
conditions herein described. Note that malfunctions as a result of water immersion or dust
intrusion caused by misuse by the customer are not covered by the warranty.
To avoid deterioration of waterproof and dust proof performance
Check the following and use the unit correctly.
ˎ The unit passes the drop test from 1.22 m (4 ft) on plywood of 5 cm (2 in) thickness conforming to ˎ
MIL-STD 810 F Method 516.5-Shock. However, this does not guarantee no damage, no breakdown,
or waterproof and dust proof performance in all conditions. Deformation or damage from
dropping the unit or subjecting it to mechanical shock may cause deterioration of the waterproof
and dust proof performance.
ˎ This unit does not have a design that is resistant to water pressure. Use of the unit in a location ˎ
where high water pressure is applied, such as in the shower, may cause a malfunction.
ˎ Do not pour high-temperature water or blow hot air from a hair dryer or any other appliance on ˎ
the unit directly. Also, never use the unit in high temperature locations such as in saunas or near
a stove.
ˎ Handle the cap with care. The cap plays a very important role in maintenance of the waterproof
ˎ
and dust proof performance. When using the unit, make sure that the cap is closed completely.
When closing the cap, be careful not to allow foreign objects inside. If the cap is not closed
completely the waterproof and dust proof performance may deteriorate and may cause a
malfunction of the unit as a result of water or dust particles entering the unit.
How to care for the unit
Although the fabric part of the unit has water repellent treatment applied, you can use the unit
more comfortably and for a longer period of time by following the maintenance procedure below.
ˎ If the surface of the unit gets dirty in the following cases, wash the unit with fresh water (tap ˎ
water, etc.) promptly to remove the dirt. Leaving dirt on its surface may cause the fabric part to
discolor or deteriorate, or the unit to malfunction.
Ex.
– When salt, sand, etc. is stuck on the unit after using it on a beach, pool side, etc.
– When the unit is stained with foreign substances (sunscreen, suntan oil, etc.)
ˎ If the unit gets wet, wipe off the moisture using a dry soft cloth immediately. In addition, dry the ˎ
unit in an airy place until no moisture remains.
ˎ The sound quality may change when water enters the speaker section of the unit. It is not
ˎ
malfunction. Wipe off the moisture on its surface, and put the unit on a dry soft cloth with the
fabric part facing down to drain the collected water inside the unit. Then, dry the unit in an airy
place until no moisture remains.
Note
ˎ If the surface of the unit gets dirty, do not use detergent, thinner, benzine, alcohol, etc. to clean ˎ
the unit because it will affect the water repellent function of the fabric part of the unit.
ˎ Especially in cold regions, be sure to wipe off the moisture after using the unit. Leaving moisture ˎ
on its surface may cause the unit to freeze and malfunction.
ˎ If sand grains, etc. enter the fabric part of the unit, remove them carefully. Never use a vacuum
ˎ
cleaner, etc. on the unit. It may cause damage of the speaker unit.
Specifications
Speaker section
Speaker system Approx. 42 mm (1
Enclosure type Passive radiator model
BLUETOOTH
Communication System
BLUETOOTH Specification version 4.2
Maximum communication range
Line of sight approx. 10 m (32 ft)*
Frequency band 2.4 GHz band (2.4000 GHz - 2.4835 GHz)
Modulation method FHSS
Compatible BLUETOOTH Profiles*
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
HSP (Headset Profile)
HFP (Hands-free Profile)
Supported Codec* 3 SBC*
Transmission range (A2DP)
20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)
1
* The actual range will vary depending on factors such as obstacles between devices, magnetic
fields around a microwave oven, static electricity, reception sensitivity, antenna's performance,
operating system, software application, etc.
* 2 BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communications between
devices.
* 3 Codec: Audio signal compression and conversion format
* 4 Subband Codec
* 5 Advanced Audio Coding
* 6 LDAC is an audio coding technology developed by Sony that enables the transmission of
High-Resolution (Hi-Res) Audio content, even over a BLUETOOTH connection. Unlike other
BLUETOOTH compatible coding technologies such as SBC, it operates without any down-
conversion of the Hi-Res Audio content*7, and allows approximately three times more data*8
than those other technologies to be transmitted over a BLUETOOTH wireless network with
unprecedented sound quality, by means of efficient coding and optimized packetization.
7
* Excluding DSD format contents.
* 8 In comparison with SBC when the bitrate of 990 kbps (96/48 kHz) or 909 kbps (88.2/44.1 kHz) is
selected.
Microphone
Type Electret condenser
Directional characteristic
Omni directional
Effective frequency range
100 Hz - 7,000 Hz
General
Input AUDIO IN jack (stereo mini jack)
Power DC 5 V (using a commercially-available USB AC adaptor capable of feeding in
1.5 A or 500 mA) or, using built-in lithium-ion battery
Lithium-ion battery life (with playback via a BLUETOOTH connection)
Approx. 12 hours*
Approx. 10 hours*
Approx. 3 hours*
Dimensions (including projecting parts and controls)
Approx. 201 mm × 72 mm × 68 mm (8 in × 2
Mass Approx. 540 g (19 oz) including battery
Supplied accessory Micro-USB cable (1)
9 Measured value acquired by playing our specified music source with the volume level of the unit
*
set to 25, the sound mode set to STANDARD, and the illumination turned off.
* 10 Measured value acquired by playing our specified music source with the volume level of the unit
set to 25 and with the factory default settings (illumination: ON and sound mode: EXTRA BASS).
* 11 Measured value acquired by playing our specified music source with the volume level of the unit
set to maxim and with the factory default settings (illumination: ON and sound mode: EXTRA
BASS).
If the built-in lithium-ion battery is running low, the maximum volume is reduced to about half to
protect the circuit. This is a specification.
The usage life mentioned here also includes when playing back music at about half the volume.
12
* Actual performance time may vary from the listed time due to the volume, songs played,
surrounding temperature, and usage conditions.
1 as specified in
2 as specified in "Degrees of protection against solid
fresh water, tap water, pool water, salt water
liquids other than the above (soapy water, water with detergent or
bath agents, shampoo, hot spring water, etc.)
Cap
2 / in) dia. × 2
3
1
2
4 , AAC* 5 , LDAC* 6
9 * 12
10 * 12
11 12
*
7 / in × 2 3 / in) (w/h/d)
8 4
System requirements for charging battery using USB
Using a commercially-available USB AC adaptor capable of feeding in 1.5 A or 500 mA
(the charging time will be shorter with a USB AC adaptor capable of feeding in 1.5 A)
Compatible iPhone/iPod models
iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s,
iPhone 6 Plus, iPhone 6, iPhone 5s, iPhone 5c, iPhone 5, iPod touch (6th generation)
The unit is compatible with iOS 10.0 or later.
Design and specifications are subject to change without notice.
Español Sistema de audio personal
POR FAVOR LEA DETALLADAMENTE ESTE MANUAL DE INSTRUCCIONES
ANTES DE CONECTAR Y OPERAR ESTE EQUIPO. RECUERDE QUE UN MAL
USO DE SU APARATO PODRÍA ANULAR LA GARANTÍA.
AVISO IMPORTANTE PARA MÉXICO
La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia
perjudicial y (2) este equipo o dispositivo debe aceptar cualquier
interferencia, incluyendo la que pueda causar su operación no deseada.
Para consultar la información relacionada al número del certificado,
refiérase a la etiqueta del empaque y/o del producto.
ADVERTENCIA
Para reducir el riesgo de incendio, no cubra la apertura de ventilación del
aparato con periódicos, manteles, cortinas, etc. No exponga el aparato a
fuentes de llama abierta (por ejemplo, velas encendidas).
No sitúe el aparato en un espacio cerrado, como una estantería o un
armario empotrado.
No exponga las baterías (el paquete de baterías o las baterías instaladas)
a calor excesivo como el sol directo, fuego o similar durante un período
prolongado.
No exponga las baterías a condiciones de temperaturas
extremadamente bajas que pueden provocar sobrecalentamiento y
fugas térmicas. No desarme, abra, ni triture las baterías. En el caso de
que una batería gotee, no permita que el líquido entre en contacto con
la piel o los ojos. Si se ha producido contacto, lave la zona afectada con
abundante agua y acuda a un médico. Las baterías tendrán que cargarse
antes de poder utilizarse. Consulte siempre las instrucciones del
fabricante o el manual del equipo para obtener las instrucciones de
carga adecuadas. Después de largos períodos de almacenamiento,
puede ser necesario cargar y descargar las baterías varias veces para
obtener el máximo rendimiento. Elimínelas de forma adecuada.
Precaución al cargar
Si la clavija USB se inserta estando húmeda, se
producirá un cortocircuito debido al líquido
(agua del grifo, agua salina, bebida refrescante,
etc.) adherido a la unidad principal y al cable de
carga o a materias extrañas, lo que puede
provocar una generación anormal de calor o un
mal funcionamiento.
No inserte nunca la clavija USB cuando la
unidad principal o el cable de carga
estén húmedos.
Precauciones
Seguridad
• Si su piel entra en contacto con este producto por un tiempo
prolongado cuando está encendido, puede ocasionar una lesión por
baja temperatura.
• La información importante, como el nombre del modelo, se encuentra
dentro de la cubierta en la parte posterior de la unidad.
Acerca de la función Party Booster
Si la unidad golpea a una persona o a una cosa, es
posible que produzca un accidente, una lesión o una
avería. Al utilizar la función Party Booster, tenga en
cuenta lo siguiente.
• Asegúrese de desconectar el cable micro-USB, etc.
de la unidad.
• Asegúrese de cerrar la cubierta mientras usa la
unidad.
• Al utilizar la función, sostenga firmemente y no
sacuda la unidad violentamente para que no la tire
ni se le caiga de las manos.
• Antes de utilizar la función, asegúrese de que ha
garantizado espacio suficiente alrededor de la
unidad.
• No golpee la unidad con una herramienta.
• No use la función mientras conduce o camina.
7
• Manténgalo a una distancia de 20 cm (7 / pulg.)
8
o más de la cara y los ojos mientras lo esté usando.
• Evite usar la función por un tiempo prolongado. Realice descansos
regularmente.
• Cuando use la función, si se cansa, se siente incómodo o experimenta
dolor en alguna parte del cuerpo, deje de usar la función
inmediatamente.
Ubicación
• No coloque la unidad en posición inclinada.
• No deje la unidad en lugares expuestos a temperaturas altas, como la
luz solar directa, cerca de una fuente de calor o bajo un equipo de
iluminación.
• No deje objetos susceptibles al magnetismo (tarjetas de efectivo,
tarjetas de crédito con codificación magnética, etc.) cerca de la unidad.
• No utilice ni deje la unidad en un automóvil.
Otros
• No coloque ni deje la unidad en lugares extremadamente fríos o
extremadamente calientes (temperaturas por fuera del rango de 5 °C a
35 °C (41 °F a 95 °F)). Si la unidad se utiliza o se deja fuera de la gama
anterior, puede detenerse automáticamente para proteger los circuitos
internos.
• Es posible que a una alta temperatura se detenga la carga o se reduzca
el volumen para proteger la batería.
• Incluso si no pretende utilizar la unidad durante mucho tiempo, cargue
la batería por completo una vez cada 6 meses para mantener su
desempeño.