Publicidad
Idiomas disponibles
Idiomas disponibles
English
CAUTION: Ensure fastener and/or system will
withstand the level of torque generated by the
tool. Excessive torque may cause breakage and
possible personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press switch to start operation. Release switch to stop
operation. Always check torque with a torque wrench,
as the fastening torque is affected by many factors
including the following:
• Voltage: Low voltage, due to a nearly discharged
battery, will reduce fastening torque.
• Accessory size: Failure to use the correct accessory
size will cause a reduction in fastening torque.
• Bolt size: Larger bolt diameters generally require
higher fastening torque. Fastening torque will also vary
according to length, grade, and torque coefficient.
• Bolt: Ensure that all threads are free of rust and other
debris to allow proper fastening torque.
• Material: The type of material and surface finish of the
material will affect fastening torque.
• Fastening time: Longer fasten ing time results in
increased fastening torque. Using a longer fastening
time than recom mended could cause the fasteners to
be overstressed, stripped or damaged.
Lift Ring (Fig. J)
DCF898
WARNING: To reduce the risk of serious personal
injury, DO NOT use the lift ring for tethering or
securing the tool to a person or object during use
when elevated.
The lift ring
is for moving the tool into difficult to reach
12
areas. Securely fasten lifting device to the ring before
moving the tool. Follow all worksite rules.
Fig. J
10
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source remove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Accessories
WARNING: Since accessories, other than those
offered by D
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
WARNING: To reduce the risk of injury, use only
WALT impact-ready accessories.
D
E
WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure
12
that they con tain no cracks.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
WALT (1-800-433-9258) or visit our website:
E
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D
Always use identical replacement parts.
WALT, have not been tested with this
E
WALT Industrial
E
WALT factory
E
WALT authorized service center.
E
WALT
E
Publicidad
