Publicidad
Idiomas disponibles
Idiomas disponibles
operating Instructions
Installing and Removing the
Battery Pack from the Tool
cAuTIoN
:
Make certain the lock-off
button is engaged to prevent switch actuation
before removing or installing battery.
To INSTAll BATTeRy PAck: Insert
battery pack (7) firmly into tool until an
audible click is heard as shown in figure
B. Ensure battery pack is fully seated and
fully latched into position.
To ReMove BATTeRy PAck: Depress
the battery release button (8) as shown in
figure c and pull battery pack out of tool.
B
Trigger Switch & forward/
Reverse Button
The drill is turned ON and OFF by pulling
and releasing the trigger switch (1). The
farther the trigger is depressed, the higher
the speed of the drill.
• A forward/reverse control button (2)
determines the rotational direction of the
tool and also serves as a lock off button.
• To select forward rotation, release the
trigger switch and depress the forward/
reverse control button on the right side
of the tool.
• To select reverse, depress the forward/
reverse control button on the left side of
the tool.
• The center position of the control button
locks the tool in the off position. When
changing the position of the control
button, be sure the trigger is released.
Adjusting Torque control
This tool is fitted with a torque adjustment
collar (3) to select the operating mode and
to set the torque for tightening screws.
Large screws and hard workpiece materials
require a higher torque setting than small
screws and soft workpiece materials.
• For drilling in wood, metal and plastics,
set the collar to the drilling position
symbol
• For screwdriving, set the collar to the
desired setting. If you do not yet know the
appropriate setting, proceed as follows:
• Set the collar to the lowest torque setting.
• Tighten the first screw.
• If the clutch ratchets before the desired
C
result is achieved, increase the collar
setting and continue tightening the screw.
Repeat until you reach the correct setting.
Use this setting for the remaining screws.
Hammer Action
Your drill has hammer action which is
engaged by twisting the torque collar to
the hammer symbol . Use hammer
action when drilling in masonry.
dual Range Gearing
The dual range feature of your drill allows
you to shift gears for greater versatility.
• To select low speed, high torque setting
(position 1), turn tool off and permit to
stop. Slide dual range gear selector (4)
away from the chuck.
• To select the high speed, low torque
setting (position 2), turn tool off and
permit to stop. Slide gear shifter button
back toward the chuck.
NoTe: Do not change gears when tool is
running. If you are having trouble changing
gears, make sure that the dual range gear
button is either completely pushed forward
or completely pushed back.
keyless chuck
WARNING
pack is removed to prevent tool actuation
before installing or removing accessories.
To insert a drill bit or other accessory:
1. Grasp the chuck (5) and rotate it in the
counterclockwise direction, as viewed
from the chuck end.
2. Insert the bit or other accessory fully
into the chuck, and tighten securely
by rotating the chuck in the clockwise
direction as viewed from the chuck end.
WARNING
or loosen drill bits (or any other accessory)
by gripping the front part of the chuck and
turning the tool on. Damage to the chuck
and personal injury may occur when
changing accessories.
Screw driving
• For driving fasteners, the forward/reverse
button should be pushed to the left.
• Use reverse (button pushed to the right)
for removing fasteners.
NoTe: When moving from forward to
reverse, or vice versa, always release
the trigger switch first.
drilling
• Use sharp drill bits only.
• Support and secure work properly, as
instructed in the Safety Instructions.
• Use appropriate and required safety
equipment, as instructed in the Safety
Instructions.
8
:
Make certain the battery
Do not attempt to tighten
:
Publicidad
