Descargar Imprimir esta página

Husqvarna YT46LS Manual De Operario página 13

Publicidad

Idiomas disponibles

Idiomas disponibles

TO START ENGINE (See Fig. 3)
When starting the engine for the first time or if the engine
has run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine.
Be sure freewheel control is in the transmission en gaged
position.
Sit on seat in operating position, depress brake pedal
and set parking brake.
Move attachment clutch to "DISENGAGED" position.
Move throttle control to choke position.
NOTE: Before starting, read the warm and cold starting
procedures below.
Insert key into ignition and turn key clockwise to "START"
position and release key as soon as engine starts.
Do not run starter continuously for more than fifteen
sec onds per minute. If the engine does not start after
several attempts, move throttle control to fast position,
wait a few minutes and try again. If engine still does
not start, move the throttle control back to the choke
position and retry.
WARM WEATHER STARTING (50° F/10°C) and above)
When engine starts, move the throttle control to the
fast position.
The attachments and ground drive can now be used. If
the engine does not accept the load, restart the engine
and allow it to warm up for one minute using the choke
as described above.
COLD WEATHER STARTING (50° F/10°C) and below)
When engine starts, allow engine to run with the
throttle control in the choke position until the engine
runs roughly, then move throttle control to fast posi-
tion. This may require an engine warm-up period from
several seconds to several minutes, depending on the
tem per a ture.
AUTOMATIC TRANSMISSION WARM UP
Before driving the unit in cold weather, the trans mis sion
should be warmed up as follows:
Be sure the tractor is on level ground.
Release the parking brake and let the brake slowly
return to operating position.
Allow one minute for transmission to warm up. This
can be done during the engine warm up period.
The attachments can also be used during the engine
warm-up period after the transmission has been warmed
up.
OPERATION
PURGE TRANSMISSION
To ensure proper operation and performance, it is rec om-
mend ed that the transmission be purged before operating
tractor for the first time. This procedure will remove any
trapped air inside the transmission which may have de vel-
oped during shipping of your tractor.
IMPORTANT:
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD
BE PURGED AFTER REINSTALLATION BEFORE OPERATING
THE TRACTOR.
1. Place tractor safely on a level surface - that is clear
and open - with engine off and parking brake set.
2. Disengage transmission by placing freewheel control
in disengaged position (See "TO TRANSPORT" in this
section of manual).
3. Sitting in the tractor seat, start engine. After the en-
gine is running, move throttle control to slow position.
Dis en gage parking brake
4. Depress forward drive pedal to full forward position,
hold for five (5) seconds and release pedal. Depress
reverse drive pedal to full reverse position, hold for five
(5) seconds and release pedal. Repeat this procedure
three (3) times.
5. Shut- off engine and set parking brake.
6. Engage transmission by placing freewheel control in
engaged position (See "TO TRANSPORT" in this sec-
tion of manual).
7. Sitting in the tractor seat, start engine. After the engine
is running, move throttle control to half (1/2) speed.
Disengage parking brake.
8. Drive tractor forward for approximately five feet then
backwards for five feet. Repeat this driving procedure
three times.
Your transmission is now purged and now ready for normal
op er a tion.
13
CAUTION: Never engage or disengage
freewheel lever while the engine is run ning.
SHOULD YOUR TRANSMISSION RE QUIRE
CAUTION: At any time, during step 4, there
may be movement of the drive wheels.

Publicidad

loading